RobinW Posted April 23, 2005 Share Posted April 23, 2005 I'm pulling together the special tools that I need to build my CSR in July and I'm currently looking at axle stands. Does anybody have a feel for the ideal height for the standsfor the chassis to be at a comfortable working height? I also need to be able to get under the car without my nose being pressed against the floor-pan. I'm looking at the 3 ton (300mm - 430mm) and 6 ton (400mm - 615mm) stands here: http://www.machinemart.co.uk/ranges.asp?g=107&r=2048 Would either of these be OK, or is there a better option somewhere? Link to comment Share on other sites More sharing options...
John Henderson Posted April 23, 2005 Share Posted April 23, 2005 From looking at the various build diaries on R300.com, it looks as if most people take a trip to Halfords. I know I did. They do two sizes and I found the larger set ideal. Reasonably priced if I remember, also. Good luck with the build. Link to comment Share on other sites More sharing options...
Frying Pan Posted April 23, 2005 Share Posted April 23, 2005 Another vote for the Halfords stands - great value 6 tons - Just how heavy is the CSR See some pictures of the build here. 5000 miles completed! Edited by - 7heavensoon on 23 Apr 2005 16:30:57 Link to comment Share on other sites More sharing options...
Normans_Ghost Posted April 23, 2005 Share Posted April 23, 2005 Robin, Don't worry about the weight rating, it's the height you need. Get the highest you can, the 6 ton look OK. The ratchet type are usefull when working but a bit narrow at the base. They'll be fine for the 7 but I would be carefull about putting to much sideways strain on them (like pushing a power bar sideways when under the car). Norman Verona, 1989 BDR 220bhp, Reg: B16BDR, Mem No 2166, the full story here Link to comment Share on other sites More sharing options...
shn7 Posted April 23, 2005 Share Posted April 23, 2005 And don't forget about how you're going to get the completed car off the stands. Steve. Link to comment Share on other sites More sharing options...
Grubbster Posted April 23, 2005 Share Posted April 23, 2005 I don't think you need anything too special - I just got 2 pairs of 'cheapies' from Screwfix - at £9.99 a pair. I think they get to about 18" high, for me this was more than enough and as Steve says - don't forget you need to be able to jack it high enough to get it back on the floor again! Roadsport build photo's here Le Mans 2004 photo's here Link to comment Share on other sites More sharing options...
LancasterBob Posted April 23, 2005 Share Posted April 23, 2005 I made some steel trestles when i built the fury, having been through it all once before at floor height with the first build i didn't want to do it again! About 4 ft tall, perfect for doing everything apart from engine/g'box and rear axle. Got the car down using engine hoist and gantry and lifting one end at a time. Rob Link to comment Share on other sites More sharing options...
RobinW Posted April 23, 2005 Author Share Posted April 23, 2005 Thanks guys! I was also wondering how the hell I was supposed to get the car down from the stands. 570Kg is a may not be much for a 3 ton axle stand, but it's a lot to lift by yourself . However, I guess I've solved more complex problems in the past, so I can't say I'm too concerned. More of a concern is being one of the first to run through the CSR build manual 😬 Link to comment Share on other sites More sharing options...
elie boone Posted April 24, 2005 Share Posted April 24, 2005 I always use chassis stands, they are much easy'er to do work underneath and are much more stable than axle stands also they don't cost much more than axle stand, or are easy to make them yourself. Link to comment Share on other sites More sharing options...
tony pashley Posted April 24, 2005 Share Posted April 24, 2005 I built my car on trolley that I made from Kee-clamps and tubing (rather like scaffolding, and the stuff they make storage towers and heavy-duty railings out of) - about 3 foot 6 inches high from memory. Once the car had all all the wheels on I got a few mates around to lift it off. I warned them that if anyone hurt themselves and sued me, I'd have to sell the car to pay them off! I had no real idea of how awkward a lift it would be - it was the idea of bending one's back to lower it that concerned me, but it was no problem at all (that was chassis, suspension, diff, wheels and tyres). The height was ideal for working on and could be rolled around for convenience or out in the sunshine! If you want to use axlestands (or chassis stands) that are taller than your jack, just hire an engine crane for the lift down although you'd need to be careful of the angles if very high or you may hit the ground at one end. Machine Mart make some stands on wheels, but they are quite expensive and a little wider than necessary, so you may keep tripping over the frames unless you fancy cutting the cross-members down. (They are about 400mm high on the largest wheel size - but they'd take the complete car with drivetrain and driver too). Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now