tiddy1 Posted March 26, 2004 Share Posted March 26, 2004 Just re-built my engine with all the good bits to get 200bhp however after 500 odd miles I seem to have a rear crank oil seal leak, its wet sumped with an apollow tank. I fitted a new seal as per instructions (assembled dry ) and fixed it in place with sealent but it still seems to be leaking. it has not moved any suggestions? could it be due to over filling the sunp? or the additional revs? I've heard that too much oil pressure when the oil is cold may be an issue? Simon Link to comment Share on other sites More sharing options...
scooby dooby doo Posted March 26, 2004 Share Posted March 26, 2004 what oil pressure do you have 🤔 Mine is fine with 90 psi cold and 75psi hot. I do have to keep the revs done when its very cold to prevent the pressure going higher. If you've go the std oil pump i doubt it will give that much pressure unless perhaps the pressure relief valve is unwell. check the oil level with it hot and running etc etc... HOOPY R706KGU Hoopylight R Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted March 27, 2004 Leadership Team Share Posted March 27, 2004 If you're getting 200 bhp I guess you've fitted TBs? If so, how good is the breathing on the cam cover? The Rover pump is strong enough to push out the oil seal, and push oil out of the various other sealed joins on the engine if the breathing is not adequate This include the cam carrier to head, and sump to block. Don't underestimate how powerfull the pump is 😬 I mention this from experience. Ensure that both venting points on the cam cover are big enough - drill bigger if necessary, then vent to a catch tank. Also, the rear crank seal should not be fitted dry - but bonded in place using a special silicon adhesive available from Rover, even though the Rover mechanics will possibly say that they always fit them dry. IIRC, product code is GEC-6000. Also worth making 2 small drillings through the steel outer rim of the new seal, into the block, thread M3, and fit 2 small bolts - belt & braces. Stu. Link to comment Share on other sites More sharing options...
tiddy1 Posted March 27, 2004 Author Share Posted March 27, 2004 Thanks stu when I said dry I ment on the crank, I have sealed the outside with sealent. Interesting point about the venting because I have blocked one of the breathers in the rocker cover. also Looks like I might have over filled it which could be the main cause, and with all this power looks like I am going to need a dry sump. oil pressure was dipping on the corners at llandow, the oil pressure light did not come on but it was definatly dropping, and I know how damped the gauges are. Simon Link to comment Share on other sites More sharing options...
Jason Plato Posted March 27, 2004 Share Posted March 27, 2004 Be double sure it is the crank seal before you remove the engine . A simple oil leak can travel an odd path an eventualy find its way due south I have seen several cam seals leak and emerge from the belhousing for instance . dave Link to comment Share on other sites More sharing options...
Slipper man Posted March 27, 2004 Share Posted March 27, 2004 Good point - I had something similar at the front, and it appeared as though the oil was coming from the front of the crankshaft. 20 mins changing the cam seal and it was all OK. Happenned at Dave's LLandow day last Spring IIRC. Link to comment Share on other sites More sharing options...
oilyhands Posted March 28, 2004 Share Posted March 28, 2004 Excess oil pressure wont harm the seal but excess crankcase pressure will. over filling will lead to windage and pulverisation / aeration of the oil, this could very likely be the cause. Make sure you vent the crankcase properly, check the breather that you blocked off for a 'pulse' while the engine is running and if necessary vent to a catch tank. oily Link to comment Share on other sites More sharing options...
Mick Day Posted March 28, 2004 Share Posted March 28, 2004 I know where the breathers are in the cam cover but where are the breather(s) in the crankcase situated? Mick Link to comment Share on other sites More sharing options...
John Howe Posted March 28, 2004 Share Posted March 28, 2004 If it is wet sump, surely through the dipstick? JH Deliveries by Saffron, the yellow 222bhp Sausage delivery machine Link to comment Share on other sites More sharing options...
Mick Day Posted March 28, 2004 Share Posted March 28, 2004 If it is wet sump, surely through the dipstick? Thanks John that's what I thought. Mick Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now