julians Posted May 1, 2001 Share Posted May 1, 2001 Does anyone know what the recommended pressure is for a 13" A032R (supersoft compound if that matters), I was going to go for about 17psi, unless anyone knows better. Link to comment Share on other sites More sharing options...
Tazio Posted May 1, 2001 Share Posted May 1, 2001 I know VX users who run them with 20 Front and 18 rear Alan Link to comment Share on other sites More sharing options...
StewartG Posted May 1, 2001 Share Posted May 1, 2001 I'd say 17psi is a good starting point maybe a bit less depending on how they wear. Link to comment Share on other sites More sharing options...
jpringle Posted May 1, 2001 Share Posted May 1, 2001 Yokohama recommend that when hot pressures should be 24psi for racing Link to comment Share on other sites More sharing options...
dba11 Posted May 1, 2001 Share Posted May 1, 2001 I run mine 18psi all round on the road, and 16psi all round when on the track. This is on a 1.8KSS. Daren. Link to comment Share on other sites More sharing options...
I.Mupferit Posted May 1, 2001 Share Posted May 1, 2001 I run mine at 18 psi all round for road use. Link to comment Share on other sites More sharing options...
Wallbanger Posted May 2, 2001 Share Posted May 2, 2001 I always use 21psi for racing. Link to comment Share on other sites More sharing options...
ashaughnessy Posted May 3, 2001 Share Posted May 3, 2001 21psi for racing? Ah, but are you talking hot or cold pressure? With my A021Rs I use 25 psi hot for racing, which means anywhere between 18psi to 21psi cold depending on the track, the weather, and also which tyre it is (e.g. nearside warms up more than offside on a circular clockwise track). I spent a day setting up at Oulton Park and played with tyre pressures and 25 psi hot was the best setting. This was measured as soon as I came off the track so the tyres didn't get a chance to cool down at all, so they were pretty hot. Its amazing how much pressure they lose when they cool down. On that day, the rear nearside went down from 25 to 17.5 ! Link to comment Share on other sites More sharing options...
Wallbanger Posted May 3, 2001 Share Posted May 3, 2001 21psi hot, the cold pressure (as you say) is dependant on track and weather conditions. That's were experience counts (I'm building mine very slowly). Link to comment Share on other sites More sharing options...
Pierre Gillet Posted May 3, 2001 Share Posted May 3, 2001 So it would seem that the 20 psi cold recommended by Caterham for road use is on the high side. I use this pressure for my AO21R 185 60 14 on the road and it might be too high. Pierre Link to comment Share on other sites More sharing options...
Steve Campbell Posted May 3, 2001 Share Posted May 3, 2001 18psi (cold) for road use on a 1.6k ss. Cheers Steve Campbell P889 GRR Link to comment Share on other sites More sharing options...
colincagain Posted May 4, 2001 Share Posted May 4, 2001 sounds like you have enough data - I use 24 hot in my 32s and I normally start out at 19 cold to see if that gets me to about the right place --- but what I do not understand is why track day advice often includes a note to increase tyre pressures by 5 psi+ over pressures used for road use - if I did this it would mean driving on the road with 14 cold - can anyone explain??? Link to comment Share on other sites More sharing options...
StewartG Posted May 4, 2001 Share Posted May 4, 2001 I do drive on the road with about 14psi cold. It's the only way I can get the rears to wear evenly, any more pressure causes more wear in the middle than on the edges. With about 14psi in the front tyres I get even wear across the front tyres too with the whole width of the tyre tread in contact with the road. I,ve seen some 32R's with the middle worn like a m/cycle tyre presumably too much pressure, god knows what the grip was like. Link to comment Share on other sites More sharing options...
Mike Bees Posted May 4, 2001 Share Posted May 4, 2001 CMC - that advice is more relevant to heavy tin-tops I'd say. Mike Link to comment Share on other sites More sharing options...
colincagain Posted May 6, 2001 Share Posted May 6, 2001 Thanks Mike - I'll never need to use it then. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now