Support Team Shaun_E Posted January 13, 2004 Support Team Share Posted January 13, 2004 Just MOT'd my car and although it passed, the inspector pointed out some play in one of the front wheel bearings and also some play in the bottom outer wishbone joint. What needs to be done to sort this movement out? Can I just adjust the wheel bearing by tightening it slightly or will it need replacing? Is there any adjustment for the suspension joint or is that a replacement too? Shaun Yellow SL #32 Link to comment Share on other sites More sharing options...
Nigel Riches Posted January 13, 2004 Share Posted January 13, 2004 Wheel bearing movement may just be a case of adjusting the nut on the stub axle to correct the free play, might be worth a look at the grease quantity in the bearing whilst doing this. As for the outer wishbone play, which type of lower joint do you have?, is it the much maligned trunnions, or do you have the later spherical bearings, if you have trunnions the play may be due to the plastic bushes on the bolt which locates the wishbone to the upright, being worn, these are included in a repair kit from Triumph dealers, (or whoever they are today) if the trunnion is worn, then the repair is more involved, removal of brake caliper, brake disc, trunnion, and reassembly, when the new trunnion is installed, I'm sure others here will offer their advice also, sounds as if your problem is quite minor, as it passed it's test this year, but should be attended to before serious problems arise. Nigel. 1982. 5 speed, clamshells. B.R.G / Ali. The True Colours. Link to comment Share on other sites More sharing options...
Support Team Shaun_E Posted January 13, 2004 Author Support Team Share Posted January 13, 2004 Nigel - thanks for the reply. I'll have a go at tightening the wheel bearing - this was covered on the "get to know your Seven" day that I attended last year so should be straightforward. I'm not sure which lower suspension joint I have - the car is a 1997 Superlight so i suspect it has the later spherical joint. Shaun Yellow SL #32 Link to comment Share on other sites More sharing options...
stevefoster Posted January 13, 2004 Share Posted January 13, 2004 You will have the spherical joint. These do go after ~12000 miles. Check that the whole unit is not moving up and down in the housing. There's a circlip under there around the upright nut holding it in. They should be bearing locked in too. Hants (North) and Berkshire Area club site here My racing info site here Link to comment Share on other sites More sharing options...
Mr Locust Posted January 13, 2004 Share Posted January 13, 2004 Make sure to keep an eye on the bearing after adjusting. If it keeps needing further adjustment then the bearing is most likely breaking up and on the way out. Ian Green and Silver Roadsport 😬 Link to comment Share on other sites More sharing options...
Support Team Shaun_E Posted January 13, 2004 Author Support Team Share Posted January 13, 2004 Thanks folks - looks like I've got my weekend jobs then 😬. If the spherical joint has gone, is replacement straightforward? Will I need a spring compressor? Shaun Yellow SL #32 Link to comment Share on other sites More sharing options...
Graham Sewell Posted January 13, 2004 Share Posted January 13, 2004 This begs the question how heavy tin tops can have suspension components that last > 200,000 miles with rigid chassis and stiff springs and yet Caterham lower spherical joints are known to fail after 12,000 miles with much lower loads?????? Low tech luddite - xflow and proud! Link to comment Share on other sites More sharing options...
Nigel Riches Posted January 14, 2004 Share Posted January 14, 2004 I think the lower spherical bearing is used in the wrong plane, ie laterally, and not as they are generally used in a radial or axial plane, thus the loading is predominantly up and down, which is felt across the races, (which are only PTFE) proper thrust bearings probably would last a lot longer, also note that these bearings are exposed to contamination, road dirt etc, the PTFE bearing life will be reduced as a consequence. Good old fashioned trunnions, now there's an idea !!!!!. All the best, Nigel. 1982. 5 speed, clamshells. B.R.G / Ali. The True Colours. Link to comment Share on other sites More sharing options...
Sheds Moderator Posted January 14, 2004 Share Posted January 14, 2004 Nigel is right, the Sph joint is hozizontal and fills up with crud. The machined surfaces are clearly visible from above and there is no rubber boot to keep the oil in and crud out. Yes, it is a crap piece of design. There is no excuse for it. Trunnions are indeed a more robust fitment *if properly maintained* if for no other reason than you can oil the bloody things. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now