darren f Posted April 14, 2003 Share Posted April 14, 2003 Thinking about some 13” track wheels and tyres for my first Seven track day (hopefully Oulton Park in July). Searching the archives for track tyres, popular opinion is that Yokohama A032Rs are good but Avon ACB10s are better. However some postings have mentioned that the suspension needs setting up for ACB10s- involving different De-Dion ears or shims etc? What exactly does this involve- I assume it’s a complete flat-floor set-up jobbie? It has been said that this is not absolutely necessary but I’d be interested in knowing where the biggest compromise would be i.e. set-up for ACBs with compromised road handling (tramlining) or not set-up for ACBs and not getting the full performance from them on track. Basically are ACBs worth all the hassle? Also, any opinions on the best wheel width and tyre combination? I’ve seen various wheel widths mentioned (6”, 6.5”, 7” up to 8.5” rears) and I assume this will have some effect on the grip / traction available. Having to learn the intricacies of RWD track driving from the beginning, I’m looking for something that’s will slide about at the limit, but to do it progressively rather than spit me into the kitty litter at every opportunity. 😳 😳 😳 😳 Thanks for any help you can offer (forgive me- so many questions due to so little knowledge!!) darren f The Building of R300SEV is Here Link to comment Share on other sites More sharing options...
Fast Westie Posted April 14, 2003 Share Posted April 14, 2003 32Rs allow you to keep the same setup for track and road. ACB10s need less camber to work properly. If you go for 32Rs try 185s all round on 6" wheels. The car in front is a Westfie1d Link to comment Share on other sites More sharing options...
SteveP Posted April 14, 2003 Share Posted April 14, 2003 Darren, Why not just run on the standard R300 15" CR500's? They should be up to the job. That's what I intend to do at Oulton Park (assuming I've got in that is) SteveP Link to comment Share on other sites More sharing options...
darren f Posted April 14, 2003 Author Share Posted April 14, 2003 Steve I was under the impression that CR500s are too soft for track work- so I'd rather keep them for road work and / or wet track use. Also having used some of the 'semi-slick' A032Rs on my Impreza previously, they seemed more suited to track use- the theory is that the large tread blocks on such tyres move about a lot less than smaller blocks (on road tyres) and the difference in grip and hence confidence in the car was quite amazing. darren f The Building of R300SEV is Here Edited by - darren f on 14 Apr 2003 12:06:07 Link to comment Share on other sites More sharing options...
darren f Posted April 14, 2003 Author Share Posted April 14, 2003 Nobody else with an opinion 🤔 All suggestions gratefully accepted 😬 darren f The Building of R300SEV is Here Link to comment Share on other sites More sharing options...
F355GTS Posted April 14, 2003 Share Posted April 14, 2003 Darren What spec is the car? if it's the R300 with circa 160BHP consider 6" with 185's on the front and 205's on 7" on the rears, or 6" alround with 185's. 32R's are a nice tyre, very predictable and grippy, go for Soft rather than Supersoft which wear quickly although I used to run my Supersport with Soft on the rear and Supersoft on the front which worked for me. Only problem with 32's is they're not very good if there is standing water with a tendency to aquaplane but htey're fine on a damp/ dry track. If you want a tyre that will also work in standing water then try the Yoko 21's in 185 alround, they are not quite as grippy as the 32's but will deal with the water. There's a new Yoko 046? I havn't tried them but Angus said they worked very well on a wet Silverstone track and were equally good in the dry on the road CR500's are pretty good but more expensive and do tend to overheat on a dry track (I believe Avon even recommend running the fronts backwards to reduce wear). Personally I found ACB10's horrible with a huge tendency to tramline and lock up under braking, also it saves changing the ears and front camber to suit as they require less camber to work well and to avoid excessive wear on the inside edges. Mark Link to comment Share on other sites More sharing options...
darren f Posted April 15, 2003 Author Share Posted April 15, 2003 Mark, Thanks for that, just the info required. It is a standard R300 so thanks for the suggestion. Running supersoft compound on the front / soft on the rear, I assume would counter understeer- is that the theory 🤔 darren f The Building of R300SEV is Here Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now