Brownmonster Posted June 27 Share Posted June 27 Hi, As per the title, I just need to use either the torque adaptor or torque wrench to tighten up the rear hub nut to 270Nm, Ideally I don't want to buy a part to use just once in the build! Would consider buying the adaptor second hand if someone wants rid. Thanks Ste Link to comment Share on other sites More sharing options...
Jonathan Kay Posted June 27 Share Posted June 27 There's a few suitable wrenches and sockets in the Equipment Register, including one in Loughborough: https://www.caterhamlotus7.club/home_folder/home_loans/tools/ NB 41 and 42mm nuts and left and right-handed threads.. Jonathan Link to comment Share on other sites More sharing options...
Ainsley Posted June 27 Share Posted June 27 I have a socket you can borrow. I just did mine as tight as I could with my normal torque wrench, but it didn't go to 270. It was enough to make sure the wheels didn't fall off for me to check the clutch / gears worked for a few yards up / down the drive. Then when it went to Caterham Silverstone, they torqued them up properly. They do this as part of the PDQ. Even my local garage didn't have a torque wrench that went to 270. Link to comment Share on other sites More sharing options...
R400svn Posted June 27 Share Posted June 27 Hi i have a torque wrench you are welcome to borrow in Rugby. Pm sent 1 Link to comment Share on other sites More sharing options...
SM25T Posted June 27 Share Posted June 27 Measure your weight and using 9.81 as a factor, stand the appropriate distance along a breaker bar. I recently did mine and stood 296mm from the centre of the shaft. Calculation for my 93kg is .... 9.81N/kg thus 270/(93*9.81)=0.296 or 296mm Link to comment Share on other sites More sharing options...
Miker7 Posted June 27 Share Posted June 27 Alternatively (and I don't recommend this) figure approx. the most you can lift with one arm. Lets say its 45kg. Then 45kg at the end of a 60cm breaker bar = (45 * 9.81) * 0.6 = 264...... So do it up BFT (blooming fffing tight) and it will be close enough. Obviously if you're capable of lifting 90kg with one arm, well done going to the gym and use a 30cm bar. Link to comment Share on other sites More sharing options...
Ainsley Posted June 27 Share Posted June 27 I would just do them up as best you can, then in the PBC they do it properly. You are not going to be ragging round the local roads - at the most you will do what I did and take it for a short pre PBC drive to check it actually work and that you can get all the gears, the brakes slow it down etc. I got 120 NM out of my torque wrench, the wheels didn't fall off 🙂 Link to comment Share on other sites More sharing options...
Brownmonster Posted June 27 Author Share Posted June 27 4 hours ago, SM25T said: Measure your weight and using 9.81 as a factor, stand the appropriate distance along a breaker bar. I recently did mine and stood 296mm from the centre of the shaft. Calculation for my 93kg is .... 9.81N/kg thus 270/(93*9.81)=0.296 or 296mm Epic. Being a physics programmer this made me smile 🙂 Link to comment Share on other sites More sharing options...
Brownmonster Posted June 27 Author Share Posted June 27 2 hours ago, Ainsley said: I would just do them up as best you can, then in the PBC they do it properly. You are not going to be ragging round the local roads - at the most you will do what I did and take it for a short pre PBC drive to check it actually work and that you can get all the gears, the brakes slow it down etc. I got 120 NM out of my torque wrench, the wheels didn't fall off 🙂 OK I'll probably do this then, my current wrench goes to 120Nm and is 40cm long, I've got an 90cm breaker bar so in theory I just need to apply the same amount of pressure at the end of that and it is happy days. Link to comment Share on other sites More sharing options...
Ainsley Posted June 27 Share Posted June 27 Yeah, so long as the wheels don't fall off while you drive it up and down the drive to check it actually works that's fine. I did take mine out for a lap of the surrounding villages with my mate following in his car checking for leaks or bits that might drop off, but I have high risk threshold 🙂 So, when will you fire it up and see if the wheels go round ? I had to adjust the clutch on mine by spannering about with the pedal box, at first the wheels wanted to go round even in neutral. But 10 mins of spannering sorted it. Its pretty cool actually making it go forwards and backwards for the first time. Link to comment Share on other sites More sharing options...
Jonathan Kay Posted June 27 Share Posted June 27 5 hours ago, SM25T said: Measure your weight and using 9.81 as a factor, stand the appropriate distance along a breaker bar. I recently did mine and stood 296mm from the centre of the shaft. Calculation for my 93kg is .... 9.81N/kg thus 270/(93*9.81)=0.296 or 296mm 24 minutes ago, Brownmonster said: Epic. Being a physics programmer this made me smile That's very polite: if you've measured your weight you don't need to multiply anything by 9.81... ; - ) Jonathan Link to comment Share on other sites More sharing options...
Brownmonster Posted June 27 Author Share Posted June 27 Haha! It'll be edited to mass before you know it... Link to comment Share on other sites More sharing options...
Brownmonster Posted June 27 Author Share Posted June 27 29 minutes ago, Ainsley said: 🙂So, when will you fire it up and see if the wheels go round ? Sometime in the next week maybe! Link to comment Share on other sites More sharing options...
Miker7 Posted June 27 Share Posted June 27 Shout if you want an audience - i'll probably be busy, but their is always a chance i'm free. 1 Link to comment Share on other sites More sharing options...
BigCol Posted June 29 Share Posted June 29 On 27/06/2024 at 11:19, Ainsley said: Then when it went to Caterham Silverstone, they torqued them up properly. They do this as part of the PDQ. I think you mean the PBC but given the cursory nature of when Caterham did mine (their lack of attention to detail led to an IVA fail) you could be right! 🤣 Link to comment Share on other sites More sharing options...
Ainsley Posted June 29 Share Posted June 29 Oh yes PBC 🙂 Doh ! Link to comment Share on other sites More sharing options...
Tom_Arundel Posted July 9 Share Posted July 9 You can hire one from the local tool shop. Or make your little clicky one twice as long Link to comment Share on other sites More sharing options...
OldAndrewE Posted July 9 Share Posted July 9 6 minutes ago, Tom_Arundel said: Or make your little clicky one twice as long It will still click at the same torque, just need half the effort to make it click Link to comment Share on other sites More sharing options...
Tom_Arundel Posted July 9 Share Posted July 9 Not if you extend from the drive end. Link to comment Share on other sites More sharing options...
ScottR400D Posted July 24 Share Posted July 24 On 09/07/2024 at 21:35, Tom_Arundel said: Not if you extend from the drive end. Good luck with that. Just buy a wrench. You can get one and a socket for <£100 and it’s pretty useful for checking wheel nuts as well as occasionally checking the hub nuts. And if you ever need to renew the bearings which isn’t unheard of…………… Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now