Stephen Long Posted December 27, 2023 Share Posted December 27, 2023 Hi guys, The oil pressure gauge on my 2007 has come apart, the case has cracked. I have tried unsuccessfully to glue this back together a few times but after a while it comes apart. Can anyone recommend a glue to stick this type of plastic. All the best Longy Link to comment Share on other sites More sharing options...
Member Jonathan Kay Posted December 27, 2023 Member Share Posted December 27, 2023 (edited) How good is the fit when you hold the bits together? If it's very good I'd clean with isopropanol and then try cyanoacrylate (Superglue). If there's any space that needs filling or a poor fit then I'd clean with isopropanol and then try epoxy (Rapid Araldite). They would both work much better if everything is warm. Whatever the adhesive I'd use something to hold the pieces together while it's setting... a cushion and some strips of masking tape might be enough. A clamp might be possible. Happy Christmas Jonathan Edited December 27, 2023 by Jonathan Kay Link to comment Share on other sites More sharing options...
Stephen Long Posted December 27, 2023 Author Share Posted December 27, 2023 Hello Jonathan, I would not say its going to be a perfect fit. Perhaps a millimetre or so gap. I have tried superglue and that is not at all successful. Araldite sounds like a good option. I will give it a go. Thank you Link to comment Share on other sites More sharing options...
Wrightpayne Posted December 27, 2023 Share Posted December 27, 2023 Lots of people have converted to mechanical gauges so I bet a wanted advert would yield a cheap replacement. Ian Link to comment Share on other sites More sharing options...
Area Representative Golf Juliet Tango Posted December 27, 2023 Area Representative Share Posted December 27, 2023 (edited) All credit to you Stephen in trying to repair it, repair is preferable to replacement. How you hold everything in place while the adhesive takes is critical (as JK mentions). But after couple of tries, replacement is in order, whether like for like or something different (which means it won't match 😟) is your decision. Edited December 27, 2023 by Golf Juliet Tango Link to comment Share on other sites More sharing options...
colindavies56 Posted December 27, 2023 Share Posted December 27, 2023 After you've glued it use a soldering iron to melt both half together. Get a paper clip and make into a Z shape and burn it in to the 2 half's to make a staple. Link to comment Share on other sites More sharing options...
7SW Posted December 27, 2023 Share Posted December 27, 2023 I had the same issue. Using Superglue did fix but for a few time. I did the repair again with bi-component blue epoxy and reinforced the result with ultra-violet resin. Since, non trouble. Link to comment Share on other sites More sharing options...
John Vine Posted December 27, 2023 Share Posted December 27, 2023 I had exactly that problem on my 2008 car: Superglue worked fine for me, but the trick (especially with non-porous materials like plastic instrument cases) is to ensure at least one of the surfaces to be stuck is moist, as cyanoacrylates require water to trigger polymerisation. I didn't need to clamp anything as the glue sets very quickly. JV Link to comment Share on other sites More sharing options...
John Vine Posted December 27, 2023 Share Posted December 27, 2023 2 hours ago, Stephen Long said: I would not say its going to be a perfect fit. Perhaps a millimetre or so gap. I missed that earlier. That gap may well prevent superglue from setting properly, in which case use a two-part epoxy such as Araldite (plus clamp). JV Link to comment Share on other sites More sharing options...
Stephen Long Posted December 27, 2023 Author Share Posted December 27, 2023 Hello 👋 This is very a interesting tip about making sure one surface is moist. I may give that a go before I move on to the araldite. Link to comment Share on other sites More sharing options...
John Vine Posted December 27, 2023 Share Posted December 27, 2023 A hint of moisture is all you need. And doing it on a damp day works wonders. More info here. JV Link to comment Share on other sites More sharing options...
Wrightpayne Posted December 28, 2023 Share Posted December 28, 2023 I’ve made effective repairs with superglue on pottery by dampening the edges - didnt think about doing the same with other materials. Link to comment Share on other sites More sharing options...
ECR Posted December 28, 2023 Share Posted December 28, 2023 Just exhaling on the joint will give enough moisture. You don’t need a lot Link to comment Share on other sites More sharing options...
PlastererPete Posted December 28, 2023 Share Posted December 28, 2023 522 RC Tyre glue is great for plastics. As the name would suggest its good for sticking rubber tyres to plastic RC wheels. I’ve used it numerous times to fix flappy rubber over-moulding back on power tools. For god sake don’t get it on your fingers it’ll stick them together faster than you can blink. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now