Glynh Posted September 3, 2023 Share Posted September 3, 2023 I'm struggling to work out where best to position the rear lift pads on my car lift. I have a 360 SV and because of the lowered floor there's very little width at the sides of the protruding floor. I need to get full access to the rear suspension components, can I position lift pads onto the lowered floor just in front of the trailing edge or will it buckle? Link to comment Share on other sites More sharing options...
Wrightpayne Posted September 3, 2023 Share Posted September 3, 2023 I lift mine on the diff (after putting the wheels on some 2"x9" so I can get the jack under) then position the stands under the rearmost chassis tube that runs behind / parallel to the fuel tank. These are positioned as far out as they'll go. My S3 has some square plates with holes in at the outer edges and I get the stands as close to these as possible.Being an SV it'll be a bit heavier/wider so just watch the tube as the weight goes (slowly) onto the stands. If you feel / see it arcing up too much then stop. Ian Link to comment Share on other sites More sharing options...
MattB Posted September 3, 2023 Share Posted September 3, 2023 This photo, taken at Caterham Gatwick's last open day, shows how Caterham put cars on a lift.MattB Link to comment Share on other sites More sharing options...
Jonathan Kay Posted September 3, 2023 Share Posted September 3, 2023 Don't they fall off?: - )Jonathan Link to comment Share on other sites More sharing options...
Glynh Posted September 3, 2023 Author Share Posted September 3, 2023 Perfect! thanks for the photos guys. Link to comment Share on other sites More sharing options...
Wrightpayne Posted September 3, 2023 Share Posted September 3, 2023 From the garages at Donington Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted September 3, 2023 Area Representative Share Posted September 3, 2023 That's on axle stands - not a lift. Link to comment Share on other sites More sharing options...
Wrightpayne Posted September 3, 2023 Share Posted September 3, 2023 Oops - misinterpreted the question! Link to comment Share on other sites More sharing options...
Glynh Posted September 3, 2023 Author Share Posted September 3, 2023 Perfecto! Link to comment Share on other sites More sharing options...
Colin Heseltine Posted September 7, 2023 Share Posted September 7, 2023 I have lowered floors and lift the car on a quicklift hydraulic lift. I have made some 19mm marine ply rubber coated boards with cutouts for seat bolts and crotch harness bolts. These sit on top of quicklift (rubber side to floor) and spread the load over the majority of the area of the lowered floor. At least 2 square foot each side.Works well and is solid, no movement.Colin Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted September 8, 2023 Leadership Team Share Posted September 8, 2023 A lowered floor has the outer edge riveted to the chassis tube with the rivets entering horizontally, unlike a standard floor where the rivets enter vertically from below. Both floor types have the rivets entering horizontally at the base of the rear bulkhead. If a standard-floored car is suspended as per the photo at Caterham Gatwick, the lifting force is directly on the chassis tube. With a lowered floor, due to the panel/rivet arrangement the weight of the car at the lifting point will be taken on rivets that are in "sheer", in my mind that would be poor practice but that's a decision down to the person doing the lifting.Stu. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now