finmac Posted July 15, 2023 Share Posted July 15, 2023 Have hardly used the car and took it out today - one of the rear calipers is binding a little. Removed the pads and cleaned them up which improved things but still not 100%. Reckon I may need a caliper?What car do they normally originate from and Best place to purchase same please? It's a 2006 R300 K Link to comment Share on other sites More sharing options...
Jonathan Kay Posted July 15, 2023 Share Posted July 15, 2023 Bigg Red are often recommended for repair kits and rebuilds.Jonathan Link to comment Share on other sites More sharing options...
elan_fan Posted July 15, 2023 Share Posted July 15, 2023 I got some from Biggred as mentioned above and am happy with themthe appear to be out of stockthey are available at Burton and maybe they are refurbished Ford if you are lucky Buton Link to comment Share on other sites More sharing options...
finmac Posted July 15, 2023 Author Share Posted July 15, 2023 That's brilliant thanks for that. Any tips for swopping them over please? Link to comment Share on other sites More sharing options...
7 wonders of the world Posted July 15, 2023 Share Posted July 15, 2023 Are you sure its the caliper that the fault and not the slides.... these often get over looked or badly maintained, and are not part of an exchange caliper either Link to comment Share on other sites More sharing options...
Jetto Posted July 15, 2023 Share Posted July 15, 2023 Just had my original Ford rears refurbished by Bigg Red, was around £150 Link to comment Share on other sites More sharing options...
Wrightpayne Posted July 16, 2023 Share Posted July 16, 2023 Has it got rigid or flexi lines? Rigid have been known to cause issues. Have you tried backing off the piston with a wind back tool? Link to comment Share on other sites More sharing options...
finmac Posted July 16, 2023 Author Share Posted July 16, 2023 rigid lines - sadly! Piston is stuck solid and the face of it is quite corroded. New caliper beckons defo.Another question - will the spring holding the handbrake mechanism take off when I loosen the 10mm holding down bolt - what's the trick with swoping the handbrake cable from one caliper to the other please? Link to comment Share on other sites More sharing options...
finmac Posted July 16, 2023 Author Share Posted July 16, 2023 Good shout re the slides, cleaned them up and the pads are now quite loose sitting in either side, so fairly sure it's the piston in the actual caliper Link to comment Share on other sites More sharing options...
SM25T Posted July 16, 2023 Share Posted July 16, 2023 Slacken the handbrake adjuster fully on the cable, then unhook it each end. Turn pistons clockwise and push hard to wind them fully home. Refit calipers and pads, ensuring pimples sit at 12-3-6-9 o'clock and thus seat in the slots on the pistons. Don't touch the handbrake lever or adjuster until you have pressed hard on the brake pedal a few times to operate the self adjusters inside pistons. Link to comment Share on other sites More sharing options...
SM25T Posted July 16, 2023 Share Posted July 16, 2023 It can be really tough to get piston rotating with the wind back tool. Sometimes need a long spanner on the hex shaft of the tool. Are you sure it's not just this ? Never be tempted to try turning it anti-clockwise !! Link to comment Share on other sites More sharing options...
Toby S Posted July 16, 2023 Share Posted July 16, 2023 Big thumbs up for Big red from me too Had the front Girling calipers refurbed by them for £200 including painting them yellow to match the nose cone and they did a really superb job for my 30 year old K series 1400 Supersport.Planning to get them to do the rear calipers this winter - not much more expensive than getting new ones - originals are off a Sierra I believe Link to comment Share on other sites More sharing options...
SM25T Posted July 17, 2023 Share Posted July 17, 2023 It is also important to replace the brake fluid every 2-3 years, as it absorbs water from the air. This sinks to the lowest point, which is of course the calipers, where is causes problems if it boils under heavy braking, and it corrodes steel parts. Easy job to bleed new fluid though until you see the colour change. Start with the furthest caliper. Link to comment Share on other sites More sharing options...
SM25T Posted July 17, 2023 Share Posted July 17, 2023 If you have a turkey baster or syringe, empty master cylinder first and fill it with new fluid before you start. Saves time and fluid. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now