madmaninshed Posted April 25, 2023 Share Posted April 25, 2023 Hi, I eventually found some nice leather s type seats to replace the older seats in my 1998 car. They fit in well, but the old ones bolted through the floor chassis members, and the bolt positions are completely different. I want to fit the new seats correctly, and if possible, without drilling too many holes, so that the originals could be refitted if somebody wanted to. If anyone has done this, I would be grateful for advice. Many thanks, Paul. Link to comment Share on other sites More sharing options...
Wrightpayne Posted April 25, 2023 Share Posted April 25, 2023 There are strengthening channels riveted to the underside of the floor with the S types Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted April 25, 2023 Area Representative Share Posted April 25, 2023 As said you need channels under the floor. I would also suggest tack welding the bolts to the runners to make fitting and tightening nuts easier. Link to comment Share on other sites More sharing options...
Graham King Posted April 25, 2023 Share Posted April 25, 2023 I did something similar on a TVR recently, I put these on the underside of the floor so that the bolts went through something more substantial than just fibreglass (which is all they do on a TVR ). Aluminium ChannelsGraham. Link to comment Share on other sites More sharing options...
alan c Posted April 26, 2023 Share Posted April 26, 2023 I did this a while ago now and from memory it is just possible to fix the Chanel's under the floor using the existing bolt holes then you need to drill new holes for the new seat mounting points. The Chanel's are also held in place with rivets, the chanel is pre drilled but you will need to drill through the floor. It all took some time to get aligned.There was a thread on here a while ago and someone made up steel (I think) plates that picked up the existing mounts and lay inside the car providing a steel section running front to back that the new seat can sit on. Link to comment Share on other sites More sharing options...
madmaninshed Posted April 26, 2023 Author Share Posted April 26, 2023 Thank you all for your advice. The channels do seem to be the correct way to do it. However, if I carefully position a seat fully back in the cockpit, and with the adjusters slid forward, I could make a flat steel bracket about 74mm hole centre to hole centre for each front seat bolt. These brackets would be bolted to the original chassis mounts, and would lie flat under the floor to where the new wider positioned seat bolts will protrude through the aluminium floor. Similar longer flat brackets could be used from the new rear seat bolts to the original rear chassis seat mounting points. Using HT bolts etc, would that be strong enough, as it can be done by drilling only 4 holes per seat, and without delay or the cost of carriage and importing parts through the French customs? Link to comment Share on other sites More sharing options...
Jonathan Kay Posted April 26, 2023 Share Posted April 26, 2023 Please could you add a sketch of what you're considering.Would it be possible to combine each of those new front and rear brackets so that they run the whole way between the two points where the load is injected into the chassis?Jonathan Link to comment Share on other sites More sharing options...
alan c Posted April 26, 2023 Share Posted April 26, 2023 Jonathansomeone has done what you are suggesting but my searches for the old thread are not finding it Link to comment Share on other sites More sharing options...
Drumster Posted April 26, 2023 Share Posted April 26, 2023 See my Post #5 on this thread Link to comment Share on other sites More sharing options...
madmaninshed Posted April 26, 2023 Author Share Posted April 26, 2023 Hi Jonathan, Please excuse sketch. It is the first time I have used this software, and I have no idea how to draw curves. The brackets would bolt under the chassis member at the front, and under the seat mount lugs at the back. Then the new seat bolts would go through both floor and brackets. Perhaps a continuous bar might be better as in Drumster's post. Link to comment Share on other sites More sharing options...
Jonathan Kay Posted April 26, 2023 Share Posted April 26, 2023 What Drumster says and shows. Continuous supports should be lighter for any given strength... JonathanPS: It's possible to link to an individual post in a thread: https://www.caterhamlotus7.club/forum/techtalk/rear-floor-given-way-drivers-side https://www.caterhamlotus7.club/comment/2250548#comment-2250548 Link to comment Share on other sites More sharing options...
Jonathan Kay Posted April 26, 2023 Share Posted April 26, 2023 "someone has done what you are suggesting but my searches for the old thread are not finding it"!Discussion of searching, and my preferred method.Jonathan Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now