ECR Posted February 6, 2023 Share Posted February 6, 2023 Just watching the assembly of an engine on u tube and it jogged a memory. I use the type of piston ring compressor that is basically multi sheave thin sheet steel wrapped in a circle with a ratchet device on the outside that is tightened with an L shaped key. It worked well for a while and then I managed to break two successive piston rings whilst using it. I couldn’t understand why. I had tightened the ratchet as much as it would go, even using the small wrench from my socket set. The answer was, that as an amateur, the tool probably only gets used once a year (if that) and the layers of steel had dried out preventing the tool from fully tightening. A smear of oil between the layers made an enormous difference. I recommend it if you use this type of tool Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted February 6, 2023 Area Representative Share Posted February 6, 2023 I have that exact tool Roger. Thanks for the tip. Link to comment Share on other sites More sharing options...
oilyhands Posted February 6, 2023 Share Posted February 6, 2023 I use a tapered piston sleeve which compresses the rings, but does *not* grip the pistons, this makes assembly easy and safe and incredibly fast, the chance of ring breakage is minimal and very little effort is required to push the pistons into the bore (one finger); if a ring snags (which is unlikely), then the resistance is easily felt. The top of the liner is tapered to allow entry with the rigs expanded. The sleeve is made from an old liner of the correct size, but Wiseco produce piston sleeves in a variety of sizes. These are very effective and cost less than a ring set. Oily Link to comment Share on other sites More sharing options...
ECR Posted February 6, 2023 Author Share Posted February 6, 2023 I prefer that type too... Link to comment Share on other sites More sharing options...
ECR Posted February 6, 2023 Author Share Posted February 6, 2023 I prefer that type too... Link to comment Share on other sites More sharing options...
Englishmaninwales Posted February 6, 2023 Share Posted February 6, 2023 +1 on the Wiseco taper sleeve, works a treat! Link to comment Share on other sites More sharing options...
Beagler Posted February 6, 2023 Share Posted February 6, 2023 https://www.amazon.co.uk/NEILSEN-TOOLS-CT2195-PISTON-COMPRESSOR/dp/B002A4HJE4/ref=asc_df_B002A4HJE4/?tag=googshopuk-21&linkCode=df0&hvadid=310822128238&hvpos=&hvnetw=g&hvrand=6244520910007659871&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9046601&hvtargid=pla-450306597302&psc=1 https://www.amazon.co.uk/QWORK-Automotive-Piston-Plier-Expander/dp/B09R1RB6K2/ref=asc_df_B09R1RB6K2/?tag=googshopuk-21&linkCode=df0&hvadid=598355288846&hvpos=&hvnetw=g&hvrand=6244520910007659871&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9046601&hvtargid=pla-1657051333910&psc=1 Link to comment Share on other sites More sharing options...
oilyhands Posted February 7, 2023 Share Posted February 7, 2023 The problems with these are..1) they grip the piston which means a lot of effort is required to insert the piston to the bore, (I've seen them tapped with the handle of a hammer), if a ring snags you wont feel it and will probably damage it2) they are spiral wound and can easily displace in use allowing a ring to creep out just before entering the bore.3) they are a faff to use as they have to be wound/unwound on every use. Link to comment Share on other sites More sharing options...
Beagler Posted February 7, 2023 Share Posted February 7, 2023 I found them ok when I was a MotorTech. Link to comment Share on other sites More sharing options...
oilyhands Posted February 7, 2023 Share Posted February 7, 2023 Yes and I used that type exclusively from 1970 until around 1998 when I made my first sleeve. For an amateur builder the sleeve makes a lot of sense, the first post here shows the difficulties that are faced and the damage that can result. Why take the chance?Oily Link to comment Share on other sites More sharing options...
Beagler Posted February 7, 2023 Share Posted February 7, 2023 I guess that In the many engines I rebuilt I must just have had the knack. Link to comment Share on other sites More sharing options...
ECR Posted February 7, 2023 Author Share Posted February 7, 2023 Me too, I had never broken a ring until I had the problem. Light lubrication does make a big difference. It allows proper tightening of the clamp (use your small ratchet to minimise the faff of tightening)and reduces ( but doesn't absolutely eliminate) the sticktion between tool and piston that oily mentions. In its favour,its (6?) times cheaper than the sleeve type and accommodates different size pistons which the sleeve doesn't. It's not a bad tool..... Link to comment Share on other sites More sharing options...
aerobod - near CYYC Posted February 7, 2023 Share Posted February 7, 2023 The piston rings on older engines were quite thick, substantial, inefficient and not as effective as on newer engines. The much thinner and more fragile modern ones need more careful fitting. The old-style brute force mechanics don't do well with the much more finely engineered modern vehicle. Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted February 7, 2023 Leadership Team Share Posted February 7, 2023 I use the expanding type and although it has shortcomings it suits my needs, also it's certainly a big step up on the split Heinz Baked Bean tin and jubilee clips I used 40 years ago on the first Mini engine I rebuilt!However, if I was assembling as many engines as Oily does and particularly the same type, I'd buy a proper sleeve. It's a no-brainer.Stu. Link to comment Share on other sites More sharing options...
Englishmaninwales Posted February 7, 2023 Share Posted February 7, 2023 Compared to the other devices mentioned, which I have previously used, I'd suggest that a taper sleeve is most suited to the occasional amateur user, like me, for its ease and significant reduction in risk of ring damage. The only downside is the cost, but I'm happy to lend it out (it's an 80 mm size). Link to comment Share on other sites More sharing options...
Mechanical Moz Posted February 8, 2023 Share Posted February 8, 2023 @ECR Was the YT vid the V12 rebuild on M539 Restorations by any chance? I was thinking the same when he was tapping the pistons in with a hammer handle as has been mentioned already. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now