abbot Posted January 29, 2021 Share Posted January 29, 2021 I took the seats out today basically to free up the runners so it is easier to adjust. Then on inspectingthe seats I have decided that the driver seat needs a refurbish.Anyone done that?The plastic back panel ha split and brocken. The foam on the side rails have come unglued and out of position.So the plan is to get a suitable sheet of plastic and use the old bit as a template. I will need to be a bit creative with my popriveter to reproduce the plastic turned back edges and folds. Link to comment Share on other sites More sharing options...
7 wonders of the world Posted January 29, 2021 Share Posted January 29, 2021 Oxted will sell you the parts you need, I had a plastic back and some padding form them a few years back, give them a bell. Link to comment Share on other sites More sharing options...
abbot Posted January 29, 2021 Author Share Posted January 29, 2021 Thanks for that. I think I will try to knock something up myself 1st. If that fails then I will call oxted. I am a bit worried anout the cost and complication of getting bits to france. Link to comment Share on other sites More sharing options...
Area Representative Golf Juliet Tango Posted January 29, 2021 Area Representative Share Posted January 29, 2021 The back can probably be cable tied into position. Could you cut it oversize and use a hot air gun to soften it enough to mould around the frame? The shell of the squab is much more difficult. It would be a proper palaver trying to get that moulded to shape. Link to comment Share on other sites More sharing options...
abbot Posted January 30, 2021 Author Share Posted January 30, 2021 just got back from DIY shop. I have bought a storage bin lid that appears the right thickness of plastic to be able to cut up into a new back panel. I got some plastic angle strip that I plan to cut and pop rivet/glue to form the edges then tie wrap onto frame. Funnily in my working career with vehicle safety I have seen thousands of seats stripped and re trimmed for the fitting and removal of Side Airbag Modules but have never laid hands on before. At the end of the day there are not particularly high tech.What can go wrong? Link to comment Share on other sites More sharing options...
abbot Posted February 2, 2021 Author Share Posted February 2, 2021 I thought I would post some pics of the refurbished activity. At the top you can see the parts used. A large container lid to provide a sheet of plastic, tie wraps to fix to frame and high density foam insulation tube for side rail padding. Not shown is a dead garden chair cover for foam backingthe seat strips down fairly easily There are a number of points where material is stitched to the plastic so my target is to keep as much as possible of the plastic with material attached and pop rivet it to the new plastic back Link to comment Share on other sites More sharing options...
abbot Posted February 2, 2021 Author Share Posted February 2, 2021 1st pic is container lid withe ribs and edges cut off to give flat sheet ready to be marked out2 trick pint was keeping the top double layer flap which allows hooking of seat material at the top2 pics of finished back plate. The original back panel would have been vacuum formed with angle edges to fix material and and a large curvature at the bottom to fit form. I achieved curvature by clamping sheet between clamps before riveting old sheet on to it im now waiting for material to dry after washing will post some more pics of final fittingalso managed to straighten the roller that holds the headrest tight to stop rattling Link to comment Share on other sites More sharing options...
abbot Posted February 2, 2021 Author Share Posted February 2, 2021 You can see the plastic angle stip riveted down the sides for fixing coverMissing pics Link to comment Share on other sites More sharing options...
Area Representative Golf Juliet Tango Posted February 2, 2021 Area Representative Share Posted February 2, 2021 also managed to straighten the roller that holds the headrest tight to stop rattling Well done. In an old, now unused seat, I'm sure I dislodged this component. This was in the days before I had a tonneau with pockets, so the headrestraint had to be removed every time I parked up. Link to comment Share on other sites More sharing options...
Alastair B Posted February 2, 2021 Share Posted February 2, 2021 Interesting to see how this develops. I contacted Oxted a short while ago about seat refurbishment cost with their kit and they said...."Our seat back refurb. kits (£53.22) contain the seat plastic and the foams found in the seat back. UK carriage is an additional £12.00."Not too bad in the whole scheme of things, plus think we might get club discount.In the end I didn't go for it, but still might in the future. For the odd hole on the seat back that had split, I ended up re-drilling the seat back holes 5-6mm inboard from where they are now and securing with cable ties, plus adding one or two new additional holes for extra load sharing. Link to comment Share on other sites More sharing options...
abbot Posted February 2, 2021 Author Share Posted February 2, 2021 if it had been pre brexit i might have gone for a kit but the cost of getting stuff to france is going up,total cost for parts so far is less than 10 quid Link to comment Share on other sites More sharing options...
Area Representative Golf Juliet Tango Posted February 3, 2021 Area Representative Share Posted February 3, 2021 I'll refrain from any comment beyond offering admiration at the make-do-and-mend approach. Link to comment Share on other sites More sharing options...
abbot Posted February 3, 2021 Author Share Posted February 3, 2021 Foam side padding tie wrapped into position Then every thing assembledi added a couple of through threads to pull it a bit tighter. Not perfect but very happy with the result. It certainly is a lot more supportive than before Link to comment Share on other sites More sharing options...
Area Representative Golf Juliet Tango Posted February 3, 2021 Area Representative Share Posted February 3, 2021 Well done.Now for the squab? Link to comment Share on other sites More sharing options...
abbot Posted February 4, 2021 Author Share Posted February 4, 2021 Thank you. No the squab is in good shape so no action required. I need to do a deeper check on the passenger seat but by definition it should not have had so much wear and tear. Link to comment Share on other sites More sharing options...
abbot Posted February 22, 2021 Author Share Posted February 22, 2021 My Feb copy of LF has just arrived.I should have waited for the article on seat refresh. Link to comment Share on other sites More sharing options...
chrism Posted November 27, 2021 Share Posted November 27, 2021 My DIY skills are not up to the original poster, but for lesser mortals I can report that the refurb process for the leather S seats using the kit from Oxted is quite manageable. The plastic back had split horizontally and all down one side, and both strips of side foam had moved. 3 hours later, the seat is as good as new. And much more fun than Christmas shopping!Many thanks to @Alan Morgan for his great article in the Feb 2021 LF which gave me the confidence to tackle this job. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now