goodcoffeecode Posted August 9, 2020 Share Posted August 9, 2020 Hi all,Just wanted to ask a few questions then get a sense-check on my plan please.Last week my 7 got a bit hot on a run. It was a hot day (28ish?) the car was sat whilst I fitted a passenger, then a 20 minute blat, 5 minutes sitting in a car park (still running) then 20 minutes slow drive home. Temp got up into the red when at traffic lights, but dropped to 80-90 when cruising at around 50-60mph.My suspicion was that the fan wasn't kicking in, so I took it out yesterday for a 30 minute blat - temp stayed around 80-85... all good. When I got home, I deliberately left it running whilst I took the nosecone off, to inspect the fan. As I got the cone off, with the temp showed around 90 (maybe near 100?), the expansion tank was in full volcano mode. Turn the engine off and ran cold water of the radiator to help cool it.Once cool, I topped up the expansion tank with just water and started it again. Temp seemed happy to sit at around 80-85, but there was a tiny bit of steam coming from somewhere in the radiator (no idea if this is normal or not?). Holding a mobile down the back of the fan, I could tell that it wasn't spinning.My first step is to make sure that there's not an air gap at the top of the radiator. My understanding is that this would stop a true temp reading being taken which, in turn, might confuse the fan. The expansion tank shows fluid up to the max line, but I understand this can be deceiving.Question 1: What's the easiest way to top up the radiator and remove any air gap? Is it going via the hex screw at the top (#1 in photos)?Question 2: Could someone name parts 2-5 and what they do please?I've ordered a new expansion cap as a precaution.After inspecting a coolant container in the garage, it clearly only contains water :(. I used this to top up the coolant a few weeks ago. I wonder if that diluted it too much and lowered its boiling point? I've checked the fan relay and fuse - which are both working.Question 3: What's the best way to test the fan? I've seen snippets of people talking about shorting wires, but I've not found an explicit set of instructions.Thanks all Link to comment Share on other sites More sharing options...
Jonathan Kay Posted August 9, 2020 Share Posted August 9, 2020 Private Messages sent. Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 9, 2020 Author Share Posted August 9, 2020 Interestingly, I've just added at least a pint to the radiator via the hex screw thing - without changing the level of fluid in the expansion tank. Sounds similar to what #jamesh experienced here: https://www.lotus7.club/forum/techtalk/k-series-coolant-level Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 With ignition on, unplug connector off thermo switch "2" and short the wires in the connector together. Fan should run. Your "4" is the single wire sender to the temperature gauge. Your "3" is a small bore hose to let air out of the head. "1" is a bleed screw to help get air out of radiator. You should have used yellow or orange for your labelling !! Yoh really want a 16mm bleed ted in the highest heater hose. Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 If you had an air pocket in the top of the radiator, the fan wouldn't switch on as it should. Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 9, 2020 Author Share Posted August 9, 2020 Hi Ian,Thanks for that. Are you sure about shorting those 2 wires together? (I assume that means "unplug them and touch them together"?). Someone else has suggested definitely not to do that.Thanks,Chris Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 Yes. That is all the switch does. Once you unplug the connector, use pliers or a bit of cable to connect between the sockets in the plug. Expect a spark, but no risk. If fan doesn't run with ignition on, check fuse. Link to comment Share on other sites More sharing options...
John Vine Posted August 9, 2020 Share Posted August 9, 2020 Agree with the above, but what on earth is item 5? Despite being an ex-K owner, I don't recognize it.JV Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 9, 2020 Author Share Posted August 9, 2020 Pulled out both wires going into thermo switch (#2 in pics), and held them together with some locking pliers. Turned on ignition and fan came on straight away.I then started the car and it took about 4 minutes for the temperature gauge to read 60. Not sure if that suggests whether or not the gauge is working correctly though. The top red hose (which, I believe, comes from the engine?) got warm in places, but the radiator stayed cold.As soon as it was turned off I also took the liberty of checking the oil - which was spot on. Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 I am guessing #5 is the temperature sender ... a 2-wire device that sends info to the ECU. Like John, I don't recognise the way it is mounted though Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 All hoses should get equally hot as engine warms up. Anything remaining cold is bad news. Suggests an airlock in there somewhere still. Link to comment Share on other sites More sharing options...
John Vine Posted August 9, 2020 Share Posted August 9, 2020 The top red hose (which, I believe, comes from the engine?) got warm in places, but the radiator stayed cold.I'd say that was normal if the gauge reading of 60C is anything like accurate. IIRC, the stat is 82C, so until that opens, the top hose (from engine to rad) will get warm but not hot. The hoses to/from the heater (the smaller red ones at the back of the engine in your photo) should get hot, however, as that's the bypass circuit until the stat opens.JV. Link to comment Share on other sites More sharing options...
John Vine Posted August 9, 2020 Share Posted August 9, 2020 Just re-reading #1:... the expansion tank was in full volcano mode.Was the "volcano" inside the expansion tank? That is, the coolant wasn't pouring out?From your photos, it looks like you have a Supersport-R. Those rollerbarrels replace the standard inlet manifold, and thus the manifold connection to the small-bore pipe to the expansion tank will no longer contain the standard "jiggle valve". As a result, there will be a constant flow from the engine to the expansion tank.JV Link to comment Share on other sites More sharing options...
SM25T Posted August 9, 2020 Share Posted August 9, 2020 If the coolant is predominantly water, the boiling point will certainly be lower. Link to comment Share on other sites More sharing options...
Wrightpayne Posted August 9, 2020 Share Posted August 9, 2020 My car has sender #5. I know Its not the temp gauge sender as thats further down the water rail. Always assumed it was sending info to the ECU. Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted August 9, 2020 Area Representative Share Posted August 9, 2020 Yes. No 5 is temp sender for ECU. You have the older water rail. Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted August 9, 2020 Area Representative Share Posted August 9, 2020 Yes. No 5 is temp sender for ECU. You have the older water rail. Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 9, 2020 Author Share Posted August 9, 2020 Hi John, I didn't check those - but I will tomorrow. I'd only checked the other large pipe connecting to the rad.So, I must confess that I don't really know how this works. When you say "until the stat opens" do you mean that the coolant flow doesn't start (going through the rad?) until it reaches a certain temp? Presumably, there's then a second, higher, temperature where the fan kicks in (82?). Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 9, 2020 Author Share Posted August 9, 2020 Here's the video of the incident: Link to comment Share on other sites More sharing options...
SM25T Posted August 10, 2020 Share Posted August 10, 2020 Yes. Flow through radiator only when mechanical thermostat on the side of the engine opens. Independenty of that, the switch on the top of the radiator turns the fan on and off at a higher temp. Typically on at 92 and off at 87. Link to comment Share on other sites More sharing options...
goodcoffeecode Posted August 10, 2020 Author Share Posted August 10, 2020 Got it. What temp does the mechanical thermostat normally open at? Link to comment Share on other sites More sharing options...
Wrightpayne Posted August 10, 2020 Share Posted August 10, 2020 82 degrees.re post #18 thats how the cooling systems work on most water cooled internal combustion engines. If there was free flowing fluid in the system engines would never reach optimum operating temperature for best fuel economy. The stat blocks 90% of the flow (the 10% is the heater, or bypass, which is a secondary circuit before the stat) until the water around the block is hot then opens up to the rad.Hope that makes sense. RegardsIan Link to comment Share on other sites More sharing options...
SM25T Posted August 10, 2020 Share Posted August 10, 2020 You can get different settings of thermostats... and fan switches. My car came with an 88C stat. I changed it to an 82C. Much nicer. Link to comment Share on other sites More sharing options...
SM25T Posted August 10, 2020 Share Posted August 10, 2020 #19. That IS a volcano. Airlock in system. Replace cap anyway. Fit a bleed tok us highest heater hose. Fill and bleed with heater valve open, so the heater matrix is filled and bled. Link to comment Share on other sites More sharing options...
Bricol Posted August 10, 2020 Share Posted August 10, 2020 The screw in the top of the radiator is lower than the expansion tank- so unless you are parked on a very steep hill, or have anti-gravity, any water poured in there will have no effect on the level in the expansion tank. What should happen is when you remove it, assuming the expansion tank is full of coolant, air, flowed by coolant should escape from the radiator, the level in the expansion tank dropping as coolant escapes. At this point, replace the screw.While plain water does have a lower boiling point than water and anti-freeze, its not making it boil over - the duff fan switch is not operating the fan, so its over heating. Your local motor factors will have something suitable if you wander in with that one - I believe the standard one is VW Golf Mk2 ish. If you go too low on the "on" temp, it will run all the time - a cheap replacement claiming 88 on did that to me.And the steam on the radiator - just the water you tipped over it to cool it evaporating off as it warms up when you ran it. If you wanted to cool it, you should have left the engine running to pump coolant around the radiator as you ran water over it - assuming of course, there was still enough coolant in the system to do so. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now