Support Team andy_harries Posted July 24, 2020 Support Team Share Posted July 24, 2020 Hi allGot a DRE shift light for my birthday (my wife is a star - no socks for me!), and having rummaged around under the dash I think I've found a couple of spare connectors to get switched live and earth, but nothing spare for the pulse signal. I'm probably going to have to tap into the wire in the loom for the tacho.Has anyone used Posi-Tap connectors for this? Seems that they are widely used for motorbikes (lots of mentions of them on motorbike forums) and apparently are resistant to vibrations and moisture. Looks like a good solution if I want to remove the shift lights in the future, rather than soldering and shrink wrapping. Found a short video of the posi-tap in action ( ) - looks like it could work?Also, just checking that I've got the right wires in the pics below. Those are the two spare connectors I found - I got very excited at the one on the left until I got closer and realised the wire is grey, not white The one on the right I assume is the green & black (live and earth) that I need.This is the tacho loom - I can see the white wire with black flash right in front - there are a couple of other white & black wires, but I assume its the white wire with the least black on it?Car is a 2015 Roadsport (I think ex -academy). Link to comment Share on other sites More sharing options...
Jonathan Kay Posted July 24, 2020 Share Posted July 24, 2020 Private Messages sent. Link to comment Share on other sites More sharing options...
ChrisC Posted July 24, 2020 Share Posted July 24, 2020 Hi Andy By 2015 the wiring diagrams published in the build manuals where way out of date, they where with my 2011 ex-academy car.Caterham uses "commonly used British car wiring colours" so a reference like this https://www.autoelectricsupplies.co.uk/page/commonly_used_british_vehicle_wiring_colours will help a lot. Obviously checking with a multi meter is the best approach. As a 2015 car, I would imagine your car is fitted with the connector for the sequential shift light option, The connector should be identifiable by the White/Black wire which is the tacho feed, and should be in the area your looking (i.e. behind the tacho, near the steering column)Hope this helps Link to comment Share on other sites More sharing options...
Support Team andy_harries Posted July 24, 2020 Author Support Team Share Posted July 24, 2020 Chris - had another dig around behind the speedo and found these - does this look like the spares that you found? There are 2 black, 1 green and 1 white/black there. If they are the ones I'm going to have to work out how to get the tape off without damaging anything! I may have to take the windscreen and scuttle off Link to comment Share on other sites More sharing options...
ChrisC Posted July 25, 2020 Share Posted July 25, 2020 Yep looks like you have found them. Black is your earth. Green 12v +ve (Ignition switched) and White Black the tach feed. Link to comment Share on other sites More sharing options...
Support Team andy_harries Posted July 26, 2020 Author Support Team Share Posted July 26, 2020 Perfect, thanks! Link to comment Share on other sites More sharing options...
Support Team andy_harries Posted July 28, 2020 Author Support Team Share Posted July 28, 2020 Sorry, back again. Got the tape off and the spare connectors out of the loom (without breaking anything else I think - result!). However, looking at them they would seem to be black with white rather than white with black.Wiring isn't my thing (give me a computer to build or software to write any day). However, looking at the wiring diagram and the colour code wiring above, as well as copious searching on here, it would suggest the spare wires are not the tacho signal ones I need. The photo below shows some of the spare wires. Theres a handy green for ignition switched power on the right, a nice black for earth in the middle, but the two other wires look black with white stripe to me.Below is the tacho loom and there is a very obvious white with back strip wire on the right - much more white than the pic above. Here's a closer pic - see the white with black stripe lower down; there is a white and back wire between my fingers that has more white than the spare ones, but less then the one with the thin back stripe.From all this, my assumption is that :- Spare live and earth are fine, I can grab those easily.- The spare black/white wires with connectors already on are not the tacho signal (can't trace them back far enough unfortunately)- I'll have to tap the white with thin back strip wire above to get the tacho signal. Link to comment Share on other sites More sharing options...
Support Team andy_harries Posted July 31, 2020 Author Support Team Share Posted July 31, 2020 Another quick update - it seems that the tap connectors don't provide enough of a connection to get the signal so I'm going to have to cut and crimp in which is annoying.Power and earth are fine though, just not getting a signal at the moment. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now