anthony1956 Posted September 27, 2018 Share Posted September 27, 2018 Addressing my greatest fear here, maybe some sagesse from BC will help. I have a 150% oversize muffler and a rear muffler, all SS fabricated by Powerspeed. Now then, I watched last time it was removed and refitted, specifically the bit where the primaries meet the muffler.. iirc that is the collector. It was one heck of a tight fit. My previous much loved safe-for-kids-in-shorts titanium exhaust wasn't it was loose until hot. Having typed this I just realised that was two different metals being fitted together, whereas the SS one is Stainless Steel throughout (meaning very-dangerous-for-kids-in-shorts).Here's the fear. If I (am able to) dismantle the SS exhaust, will I be strong enough to fit it back together (read slot silencer in to collector), and on my own? I suspect not. My wife maybe could do it.. she's stronger than me except where shopping is concerned...The impact of this tale is fundamental to decisions I am making in real time while in a break-down situation somewhere in a remote area of France. Decisions are now made. However, what do we think? Regrettably me no Spring chicken any more and I was never known for my physical strength (to put it more politely than several mechanics I know well).Are there any tricks to this process? How does one gain leverage? Is that possible? Anthony Link to comment Share on other sites More sharing options...
SM25T Posted September 27, 2018 Share Posted September 27, 2018 On mine it is a case of pull ... twist.... wiggle to separate joints. More effective than whacking it with hammer and timber cushioning. Link to comment Share on other sites More sharing options...
DJ. Posted September 27, 2018 Share Posted September 27, 2018 I have found loosening the primaries makes it easier to wiggle the collector off, but it is the standard stainless system. One man job for me each time I have done it Good luck getting your car going!Duncan Link to comment Share on other sites More sharing options...
Alastair B Posted September 27, 2018 Share Posted September 27, 2018 A good friend showed me how to do this, loose primaries and then a combined movement of circular and wiggle movements combined with a firm pressure/push from the rear at the same time. Not too physical at all but a definite knack Link to comment Share on other sites More sharing options...
anthony1956 Posted September 27, 2018 Author Share Posted September 27, 2018 ah, I need to make it clearer, this is not a standard stainless system. It's custom made and practically an interference fit; THAT's the fear full problem - not forgetting it also has a back box. Link to comment Share on other sites More sharing options...
Area Representative Nick Chan Posted September 27, 2018 Area Representative Share Posted September 27, 2018 Hi Anthony, to separate is definitely a wiggle and tug to get the system apart and I leave the primaries firm to get a decent purchase on them. Refitting is much easier though when its all apart. i attach the primaries loosely to the head, apply exhaust paste or copper grease if a good fit and this helps massively with getting the collector and then silencer(s) into place. when its all fitted, I can then tighten the primaries and all the other joints as needs be and get it aligned properly. Not much effort at all to assemble on to the car. Link to comment Share on other sites More sharing options...
anthony1956 Posted September 28, 2018 Author Share Posted September 28, 2018 grease! What an excellent idea and so obvious it never occurred to me. While perusing this thread it has also struck me that maybe I can remove the side exhaust without dismounting the rear section, I need to check access to the connection between the two, very little space without it being at least off the ground and preferably on a lift; this connect is behind the rear NS wheel, so close to the ground I have had a skid/ski welded on, which gives a new meaning to surfing. I think really it's probably at least a two man job, there are just too many (heavy) parts and they stretch the length of the car. It's huge and it can't be at all light weight.Anthony Link to comment Share on other sites More sharing options...
DJ. Posted September 28, 2018 Share Posted September 28, 2018 Beware of using copper grease on exhaust components close to the cylinder head. My brother has an Esprit and used copper grease on the nuts holding the manifold to the head. When he tried to remove the cracked manifold the nuts were irreversibly fused to the studs with melted copper- it worked like brazing. Result engine out and cutting the manifold into small pieces with an angle grinder............ Link to comment Share on other sites More sharing options...
anthony1956 Posted October 2, 2018 Author Share Posted October 2, 2018 grief! :-)car is now with a garagist and I'm going to go along and see for myself if I can do it, but if I can't, he can :-) Link to comment Share on other sites More sharing options...
anthony1956 Posted October 3, 2018 Author Share Posted October 3, 2018 ok, so Mr Mechanic commented how very difficult it was to extract the puffler. He says one of the primaries is larger than the other three in diameter and that's why the tight fit. No 3 I think. Putting it back on this evening seemed remarkably easy - though he's a strong fellow (compared to me) so that may be making it look easier.Anthony Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now