huwp Posted October 7, 2017 Share Posted October 7, 2017 Can anyone advise on the nm range I need a torque wrench to cover for most DIY servicing jobs on a 7? Any particular recommendations for actual wrenches would be great. Huw Link to comment Share on other sites More sharing options...
SM25T Posted October 7, 2017 Share Posted October 7, 2017 I have a big Clarke one (1/2" drive up to 250 Nm ?) from Machine Mart ... and recently added a baby one from the same range (CHT674 1/4" drive 5-25 Nm) Link to comment Share on other sites More sharing options...
oilyhands Posted October 7, 2017 Share Posted October 7, 2017 You need two, as suggested by SM25T, I have three, 1/4” 5-25nm, 3/8” 10-105nm, 1/2” 20nm-250nm, it overs everything from the m7 crank sensor bolt(8nm) to the crank pulley bolt (205nm).Oily Link to comment Share on other sites More sharing options...
Jim 123 Posted October 7, 2017 Share Posted October 7, 2017 With the exception of the rear hub nuts that require an eye watering 270Nm torque during build, everything else sits below 81Nm. You may want to have a look at the Build Manual (around page 186) and spec a torque wrench that fits with what you would envisage you will need.I have a calibrated Draper 30 Nm to 210 Nm which deals with most suspension, wheel nuts, and and A Frame attention. It has a long lever arm which is great at higher torque setting. But a word of caution, for many under bonnet tinkering type jobs, that wrench is just too long given the restricted access. Also there are many jobs, such as sump plug etc. where you will want to set torques below 30Nm and have something that is short, light, and easy to manipulate. I use a short Draper 10 Nm to 80 Nm for this type of work and it gets regular use.. Link to comment Share on other sites More sharing options...
Member Jonathan Kay Posted October 8, 2017 Member Share Posted October 8, 2017 I don't have the nerve to do things to the engine so what Jim says goes. For the build I bought a 1/2" Williams 20 to 140 Nm. And borrowed a big one for the rear hub nuts: there are now several of those in the register of equipment for loan. (Others recommend a lever and known weight... )NB Club discount at Halfords.JonathanPS: To my disgust I'm now supposed to use a torque wrench on various bits of bikes. So I bought a little 1/4" beauty from Lifeline which covers 2 to 24 Nm. It looks identical to this. Link to comment Share on other sites More sharing options...
Jim 123 Posted October 8, 2017 Share Posted October 8, 2017 Thanks for sharing the link Jonathan. I've just got to have one of these 2 - 24 Nm wrenches for my Toybox! Link to comment Share on other sites More sharing options...
Area Representative Geoff Brown Posted October 10, 2017 Area Representative Share Posted October 10, 2017 For my latest build I binned my old torque wrenches & purchased the Halfords Professional reversable wrench with a half inch drive & 40-225 lbf ft/60-300 Nm range.Good for hub nuts & other high torque loadings.Also purchased the lower range wrench (8-60 Nm) for all the other requirements.The Halfords Pro range has always received good reviews & has come top of the pile several times in the Auto Express tests.Cannot fault them. They are not cheap but get 10% off with the club Halfords Rewards voucher. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now