tommyg Posted December 21, 2015 Share Posted December 21, 2015 So having struggled with my better half at the weekend, this was a much more difficult job than I expected.Therefore, anybody got any tips on how best to install?The two tips I have already learnt:1) Make sure your propshaft is the right size (yes, Derek confirmed this morning I have the wrong one.....cannot be delivered until after Christmas )2) Use the jack to take the weight.As I now have 2 weeks until I start again....any more tips please? Link to comment Share on other sites More sharing options...
SM25T Posted December 21, 2015 Share Posted December 21, 2015 Assume you mean fitting the diff. Make sure propshaft is in place ... if the engine and gearbox are fitted.. without the a-frame there is plenty of space to lift the diff on a trolley jack ... I use a bit of plywood about 300 x 300mm on the arm of the jack to help balance the diff. Link to comment Share on other sites More sharing options...
Jonathan Kay Posted December 21, 2015 Share Posted December 21, 2015 It's notoriously difficult... sometimes. And that's with the right prop shaft.There may be some hints in the numerous threads on the subject, but I'm not convinced there's a single magic trick.I think someone bench pressing from below may be more manoeuvrable than a jack.Jonathan Link to comment Share on other sites More sharing options...
SM25T Posted December 21, 2015 Share Posted December 21, 2015 Jack easy and safe for me ... working solo. Link to comment Share on other sites More sharing options...
Area Representative nickhi Posted December 21, 2015 Area Representative Share Posted December 21, 2015 I removed the wooden base in the boot (four screws I remember) and used an engine hoist to lift it up into place. This made it easy to get underneath to position it without the jack etc in the way.Nick Link to comment Share on other sites More sharing options...
SM25T Posted December 21, 2015 Share Posted December 21, 2015 Much easier with boot floor out ..... easier to insert bolts ...... and swing a hammer to persuade lo g one through ! Link to comment Share on other sites More sharing options...
Jonathan T Posted December 22, 2015 Share Posted December 22, 2015 I slid underneath the car with the diff on the floor to my right, then dragged it onto me and then 'benched pressed' it (maybe struggled would be a better description), into place. We had some 8mm studding ready to slide into to top bolt hole - once on end was in (and hence some of the weight supported)I could adjust my grip and get the other side of the top bolt hole aligned so that the studding could slide completely through. I did try using a jack, but wasn't happy to proceed as there's not much space / control. You'll need someone who can steady it and slide the rod in. Total time using that method - about 10 mins. Once it's got some support the two other bolts are easy. The studding was wrapped in insulating tape to ease its passage.Good luck. Link to comment Share on other sites More sharing options...
tommyg Posted December 22, 2015 Author Share Posted December 22, 2015 Thanks all! Link to comment Share on other sites More sharing options...
Tony Whitley Posted December 22, 2015 Share Posted December 22, 2015 It is suggested that you stay away from the brown acid Link to comment Share on other sites More sharing options...
Roadsport06 Posted December 22, 2015 Share Posted December 22, 2015 I bench pressed mine into position, held it in place with one hand and started putting the top bolt in place. I was stronger and more stupid then though. Link to comment Share on other sites More sharing options...
pugwash Posted December 23, 2015 Share Posted December 23, 2015 Duct taped it to the jack so it wasn't going anywhere (lots of tape) but still with a bit of flexibility to allow for some wiggle. Then with help of son, popped a screwdriver in each hole to get the alignment about right. Then the fun started. For me the bottom bolts were simple but the long one across the top was a compete pain. My feelings on this are well documented! In the end used the multi socket extension bar technique to twist the bush sufficiently and voila!i did start with the bench press approach but found I was bench pressing the entire rear end of the car off the stands, which did not feel good at the time! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now