Area Representative Paul Richards Posted December 12, 2014 Area Representative Share Posted December 12, 2014 I've got an MBE 9A4 ECU which I want to use on my EU2 1.8K which currently uses the standard Mems ECU. What is the easiest/best way of wiring it? It would be ideal if there were an adaptor, but I guess not. What have others done?By the way, interested in a lead to connect MBE to laptop if anyone has one surplus to requirements. Link to comment Share on other sites More sharing options...
Adrian Williams Posted December 12, 2014 Share Posted December 12, 2014 I'd expect swapping the engine loom would be the easiest way Paul, I know a club member that did this a few years ago having found a used loom from an R***. Link to comment Share on other sites More sharing options...
Molecular--Bob Posted December 13, 2014 Share Posted December 13, 2014 Emerald do an eu2 adaptor, but you would have to cut the Emerald plug off and repin it and then use the mbe connector Link to comment Share on other sites More sharing options...
John Hughes Posted December 18, 2014 Share Posted December 18, 2014 PaulI will know if I need my MBE lead after tomorrow night Link to comment Share on other sites More sharing options...
Titanium7 Posted December 18, 2014 Share Posted December 18, 2014 Just wired one in myself Link to comment Share on other sites More sharing options...
Simon.Rogers Posted December 18, 2014 Share Posted December 18, 2014 PaulThe pin out/in order for the 9A4 is different to the 967 that the loom will be matched to.The 9A4 pin outs are available on SBD's website. You will have to re configure the order. It should then work. Link to comment Share on other sites More sharing options...
aerobod - near CYYC Posted December 19, 2014 Share Posted December 19, 2014 If you have to re-pin for the 9A4 ECU and you don't currently have the 36-pin connector, you can purchase it and the separate pins from SBD. I found it imperative to use a proper ratcheting crimping tool if you have to change the pins, a 0.5-1.0 mm^2 open barrel crimper is needed, I purchased this one for the equivalent of £45 that has interchangeable jaws for all common crimp connections: http://www.princessauto.com/en/detail/7-pc-professional-quick-change-ratcheting-wire-terminal-crimper-kit/A-p8355331e I'm not sure if it is available in the UK, as the vendor is Canadian, but I'm sure an equivalent can be found.Here is the pinout info: http://www.sbdev.co.uk/Info_sheets/MBE/9A4-PinoutIssue%20F.pdfThe connector that is needed (including pins) is the LM-36W (see the bottom of the page): http://www.sbdev.co.uk/Engine_Management_Systems/Fuel_Inject_Looms_Standard/Wiring_Looms_Standard.htm Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted December 19, 2014 Author Area Representative Share Posted December 19, 2014 Thanks for your help. Forgive the novice questions.If I understand correctly I simply need to take the existing plug of my engine loom and swap for an MBE plug?I get the MBE pin out wiring diagram from SBDs website. I just need to know which of the existing loom wires connect to what.Anyone got a wiring diagram for my MEMS ECU? Link to comment Share on other sites More sharing options...
Simon.Rogers Posted December 19, 2014 Share Posted December 19, 2014 Sorry Paul. I thought you were starting with an MBE 967 loom. I would not even attempt to butcher the MeMS - you will have nothing left. Find an MBE loom and start there but its still quite a bit of work. I would get a bespoke loom made. I have some numbers if you need them. Link to comment Share on other sites More sharing options...
Area Representative Paul Richards Posted December 19, 2014 Author Area Representative Share Posted December 19, 2014 Thanks for your advice Simon. If I understand correctly, SBD do a loom for a rear wheel drive car here and it looks like this will be my best starting point unless someone has a loom from an Rxxx that they want to move on.Alternatively I might sell the MBE ECU and go for an Emerald ECU. Link to comment Share on other sites More sharing options...
aerobod - near CYYC Posted December 19, 2014 Share Posted December 19, 2014 If you have the pin out for the MEMS ECU and at least about 50mm of slack in the current loom to the ECU, it is fairly straightforward to re-pin to the MBE ECU 36-pin plug. I've changed and added pins on my 9A4, the most important things are to take your time and obtain the right crimping and stripping tools (I see Farmell have suitable crimpers) get some spare pins from MBE and practice a few crimps before doing the real loom. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now