zetec Posted May 22, 2014 Share Posted May 22, 2014 Do I need a lambda sensor? I don't need it for emissions so do I need it? Link to comment Share on other sites More sharing options...
Guest Posted May 22, 2014 Share Posted May 22, 2014 Lamba sensor is not for emission. It's to calibrate the injection. To determine how much fuel the injectors should spray inside the engine. Link to comment Share on other sites More sharing options...
Pendennis Posted May 22, 2014 Share Posted May 22, 2014 No you don't need it Craig Link to comment Share on other sites More sharing options...
Garth Posted May 22, 2014 Share Posted May 22, 2014 But does it not only regulate below a certain rev limit - so can help with emissions? Link to comment Share on other sites More sharing options...
Pendennis Posted May 22, 2014 Share Posted May 22, 2014 But he doesn't need it for emissions, thus smoke only MOT. It is not needed during calibration at the RR as the operator would shove his version up yer exhaust and once calibrated, that's that 😶🌫️ Link to comment Share on other sites More sharing options...
Birkin S3 ZA. Posted May 22, 2014 Share Posted May 22, 2014 My Omex 600 runs without one on my Duratec, it would only be needed for emissions or without for less complexity. It idles great with the scatted spark control, I always thought you liked your side drafts Chris. Link to comment Share on other sites More sharing options...
zetec Posted May 22, 2014 Author Share Posted May 22, 2014 I do, hugely but things must move onwards!! I needed to get rid of very old weber alpha system & some jenveys came up too. Didn't want to do it this quick but it's gunna happen now 🥰 Link to comment Share on other sites More sharing options...
keybaud Posted May 22, 2014 Share Posted May 22, 2014 A wideband lambda sensor is used by whoever maps the ECU and engine, whereas a narrowband lambda sensor, what most cars now have, just adjusts the fuelling at low and steady revs to improve fuel economy. i.e. Cruising on a motorway should give better fuel economy with a lambda sensor fitted. My Omex 600 was mapped, but I didn't have the narrow band lamnda sensor with me, so it wasn't setup for it. I added it later and the engine ran too rich at steady revs, so I removed it. I'll bring it the next time I get the engine mapped again. There are some intelligent ECUs now appearing in the USA, which use a wideband sensor and continually map the ECU. No more rolling road sessions! Edited by - keybaud on 22 May 2014 19:31:45 Link to comment Share on other sites More sharing options...
zetec Posted May 22, 2014 Author Share Posted May 22, 2014 That's what I was hoping it would be for but as above its on for emissions anyway. Link to comment Share on other sites More sharing options...
Phil B Posted May 22, 2014 Share Posted May 22, 2014 Craig, The Omex 600 can only work with a narrow band lambda. There is a page in Map3000 where you can set the maximum trim authority that it can exercise. The settings you can adjust are revs below which it will trim, engine load % (TPS) below which it will trim and max % fuel trim (injector pulse duration). When the Steve's mapped my car they used their Wideband probe. They then put my narrowband probe in and set the authority so that it trims to achieve lambda 1.0 up to motorway cruising speeds (3500rpm around 30% throttle and max 15% fuel trim) if I remember correctly. So the lambda trim only operates when I am cruising the motorway, bimbling through town or at MoT time (even though I am visible smoke only). This set up helps me get up to 40mpg on longer runs, but doesn't stop the grin when blatting 🥰 Phil Link to comment Share on other sites More sharing options...
zetec Posted May 22, 2014 Author Share Posted May 22, 2014 So, I do need one then? I'm confused now Link to comment Share on other sites More sharing options...
7 wonders of the world Posted May 22, 2014 Share Posted May 22, 2014 Are you running with a cat? If not have it mapped with a wideband - normal process for the likes of Emerald and 2 steves, after this you should then be able to run in open loop format ie without lambda control, this will allow the engine to use the fuel map that was preset by whoever mapped it and will give much better fuel economy on cruise as it will (depending on engine spec) lean off to 18+:1 whereas a Lambda will maintain 14.7:1 - in order to keep the cat happy. So no cat, proper map, open loop = job done, Again MOT emissions can easily be exceeded with a good map Link to comment Share on other sites More sharing options...
zetec Posted May 22, 2014 Author Share Posted May 22, 2014 Cool, no lambda then Link to comment Share on other sites More sharing options...
Phil B Posted May 23, 2014 Share Posted May 23, 2014 Craig, You don't need a lambda probe to run an Omex 600 and TBs. But you do need the boss for one to be fitted when it gets mapped. Phil Link to comment Share on other sites More sharing options...
zetec Posted May 23, 2014 Author Share Posted May 23, 2014 Got one :) Cheers Phil Link to comment Share on other sites More sharing options...
andy couchman Posted May 23, 2014 Share Posted May 23, 2014 If the boss has been fitted for a while, you might want to check it can be undone easily before RRing. They can get very settled... 😔 My crossflow runs an Omex (710 in my case) and on our Alps run last year we averaged about 35mpg, which was about 10mpg better than I used to get on carbs, although too be honest, I don't always record fuel consumption, so that might have been especially good. Andy Link to comment Share on other sites More sharing options...
Pendennis Posted May 24, 2014 Share Posted May 24, 2014 Not that it is relevant but for clarity the RR will have a sensor that pops into the silencer so a lambda boss is not necessary Link to comment Share on other sites More sharing options...
OliverSedlacek Posted May 26, 2014 Share Posted May 26, 2014 You will probably also need two or three extra relays (and fuses). One is to energise the fuel pump, the second is for the coils and injectors, and the third (optional) is to control the radiator fan. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now