magister Posted March 9, 2013 Share Posted March 9, 2013 POBC My Focus 1.6TDCi needs a new EGR valve, but the new EGR will need reprogramming after fitting. Main dealers are asking around £450 to replace / reprogramme the EGR. 😳 I can get an after market unit for around £175, but if I fit it myself, there is a chance the car might not start because of the programming. I have removed the EGR and cleaned it (though it w as pretty clean) but it hasn't made any difference. Anyone know of a garage in the Leicester area who can fit an EGR and who has the necessary software to reprogramme it? (without the main dealer prices!) Any suggestions most welcome! PaulB Link to comment Share on other sites More sharing options...
Grim Reaper Posted March 10, 2013 Share Posted March 10, 2013 Does the ECU not just need the fault code clearing? An OBDII reader should be able to do that. Have a read through these here and see if there is a service bulletin that says to reprogram the EGR without changing it to, in effect, stop the fault occuring in the first place. Then try and persuade the garage that they should try that first before changing the EGR unneccesarily. Edited by - Grim Reaper on 10 Mar 2013 18:46:35 Link to comment Share on other sites More sharing options...
Belper Cat Posted March 10, 2013 Share Posted March 10, 2013 Think there are quite a lot of these being driven around after blanking off with a piece of aluminium.. Maybe a bit of 7 up tin 😬 might do the trick? Link to comment Share on other sites More sharing options...
Rob Walker Posted March 11, 2013 Share Posted March 11, 2013 I have several brand new EGR valves off new 2L and 2.3L ford duratecs if they are the same as the focus happy to sell you one for a lot less than £175 Rob Link to comment Share on other sites More sharing options...
michaeljclark Posted March 11, 2013 Share Posted March 11, 2013 Quoting Belper Cat: Think there are quite a lot of these being driven around after blanking off with a piece of aluminium.. Maybe a bit of 7 up tin 😬 might do the trick? I know that on my old "Euro 3" spec TDCi in my old X-Type this was possible, but I believe in that the Euro 4/5 spec engines need a 7mm hole drilled in the blanking plate to avoid upsetting the onboard computer. BTW PaulB - is it deffo the EGR that's gone? - I had mine replaced by a Jag main stealer only to find it wasn't the EGR that had had gone - it was the wiring loom that controlled it! Mike Link to comment Share on other sites More sharing options...
Nov-07 Posted March 11, 2013 Share Posted March 11, 2013 Magister, what are the symptoms? Do you have an "electronic" throttle pedal? A family Focus, same spec, was cured simply with a replacement pedal sourced from Amazon. Link to comment Share on other sites More sharing options...
LesG Posted March 11, 2013 Share Posted March 11, 2013 How do you know your car 'needs a new EGR valve' ? Make sure your car has been CORRECTLY diagnosed before sourcing and blind-fitting new parts. Take your car to a respected diagnostic technician, not always easy I know, but worth it in the long run. Link to comment Share on other sites More sharing options...
magister Posted March 11, 2013 Author Share Posted March 11, 2013 Thanks for all the replies. Local garage read the fault codes which pointed to the EGR. He reset the engine management light, but it came on a few miles later. I have read that EGR should click a few times when the engine is turned off (valve opening / closing to stop it getting stuck). It doesn't do this. This made me think it could be the stepper motor which controls it. Equally, I suppose it could be a wiring fault. Symptoms are: management light on, power down quite a bit but running ok. PaulB Link to comment Share on other sites More sharing options...
Nov-07 Posted March 11, 2013 Share Posted March 11, 2013 We had a similar experience with diagnostic codes, but the behaviour was worse. The management light would come on and the engine would lose power, sometimes during an overtaking attempt If the engine was stopped, then started again, all was well. The faulty component was the accelerator pedal which was easily fixed in 5 minutes. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now