Ged Posted August 7, 2012 Share Posted August 7, 2012 Been having an ongoing problem with the wipers not parking correctly. The cars a R300 Duratec with the new style push button dash. The wipers are parking themselves when I switch them off rather than going to the park position at the bottom of the screen. When on intermitent, rather than two sweeps then park for for a few seconds, they seem to be doing one and a bit sweeps then parking at any position on the screen. Same when I use the wash wipe. Anyone got any idea's, is the parking system built into the motor, or a separate module? Could it be a bad connection? Any advice gratefully received. Going aero is not an option Link to comment Share on other sites More sharing options...
Eugene Posted August 7, 2012 Share Posted August 7, 2012 Going aero is not an option I can't help then 😬 😬 😬 Link to comment Share on other sites More sharing options...
The Pikey Posted August 7, 2012 Share Posted August 7, 2012 The park switch is in the motor. When the wipers are in any other position than parked the switch sends a +12v out on a wire which is then sent back to the slow speed wire when the wipers are switched off via the old style rocker switch. On yours I would think it will go to the relay module that works a lot of the electrics in your car. Other than that I haven't got a clue how it's wired so unless anyone else has an idea I think a call to Caterham technical would be a good idea. Jason Link to comment Share on other sites More sharing options...
Ged Posted August 8, 2012 Author Share Posted August 8, 2012 Thanks Jason, I think a call to Caterham cars is in order. Link to comment Share on other sites More sharing options...
Ged Posted February 7, 2013 Author Share Posted February 7, 2013 Sorry to resurrect this, but has any one else come across this problem yet? I changed the parking switch last year to no avail, and have just plugged in a new motor, from Caterham with no success. I'm a bit stumped now, suppose the only other thing is the relay module. Link to comment Share on other sites More sharing options...
Stationary M25 Traveller Posted February 7, 2013 Share Posted February 7, 2013 Has to be worth a try !! Any similar vintage cars locally so you could try swapping the relay to see if it cures it ? Link to comment Share on other sites More sharing options...
Ged Posted February 7, 2013 Author Share Posted February 7, 2013 No other local cars the same, that I know of. Unfortunately it's not a £4 relay, it looks the same as this here but for a R300 Link to comment Share on other sites More sharing options...
Stationary M25 Traveller Posted February 7, 2013 Share Posted February 7, 2013 Crikey. That looks complex. Can you identify and change one component ? Still under warranty ? Link to comment Share on other sites More sharing options...
Ged Posted February 7, 2013 Author Share Posted February 7, 2013 I don't think individual parts can be changed, that's if I could identify what is causing the problem. Unfortunately it's out of warranty. Link to comment Share on other sites More sharing options...
charlie_pank Posted February 8, 2013 Share Posted February 8, 2013 Downgrade to what the rest of us have: I click for slow, 2 clicks for fast. Link to comment Share on other sites More sharing options...
Stationary M25 Traveller Posted February 8, 2013 Share Posted February 8, 2013 Good point. Can you disconnect the wiring from the switch and the wiper motor and rewire the switch to a new free-standing relay, or is the wiring and control board you linked to earlier all integral ? Edited by - Stationary M25 Traveller on 8 Feb 2013 07:56:19 Link to comment Share on other sites More sharing options...
elie boone Posted February 8, 2013 Share Posted February 8, 2013 Could it be that the fault is in the connector ? i.e. no + supply to the pin that feeds the park switch Link to comment Share on other sites More sharing options...
Ged Posted February 8, 2013 Author Share Posted February 8, 2013 I've definitely got a permanent 12v to feed the park switch, 12v for intermittant/slow speed, 12v high speed and an earth. Not sure what the 5th pin does. Going to have another go tonight, with a dismantled park switch and voltmeter. If this fails I think I'll take to a local auto electrician, see what they make of it. Link to comment Share on other sites More sharing options...
tbird Posted February 9, 2013 Share Posted February 9, 2013 Ged is this post re wiring any help wiper pin outs Tim Link to comment Share on other sites More sharing options...
Ged Posted February 9, 2013 Author Share Posted February 9, 2013 Thanks tbird and others. Had another go last night, but didn't get anywhere. I'm pretty sure it's not the motor or the park switch, that only leaves the electronic control module. Think I'll book it into a decent auto-electricians, see if they can sort it, even if they have to re-wire it through it's own relay. Might ask them to fit an extra push button, for a single wipe. Link to comment Share on other sites More sharing options...
Ray Pearce Posted February 9, 2013 Share Posted February 9, 2013 But the self-park shouldn't rely on the electronics at all. If the parking pin is a permanent 12 v (it should be) and the park switch is working then the wiper motor should be permanently powered until it reaches the park position. The electronics are only used to start/keep the wipers moving and to select which speed. With the wipers stopped in mid sweep, you should be able to trace the 12 v from the park feed through the park switch to the motor. When the volts stop you have found the failing part. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now