Leadership Team SLR No.77 Posted November 12, 2010 Leadership Team Share Posted November 12, 2010 Technical POBC ...... When I had my last car (K-Series), following fitting a dry sump system I bought the Caterham ally tensioner pulley which unfortunately I didn't get round to fitting. I now have the engine out of my new car and plan to swap to the ally pulley ..... but how is the pulley located onto the bearing? Is it just a press fit? Bearing lock? There would appear to be a groove, that although a little wide could possibly take a sizeable circlip? Also, which way round does the pulley go? Wide flange front or back? Questions questions questions!!! Stu. Joint Area Representative MAD Sevens (Merseyside And District) www.superse7ens.co.uk..........the rebuild 😬 Link to comment Share on other sites More sharing options...
mav Posted November 12, 2010 Share Posted November 12, 2010 Pretty sure I've got a circlip int he bag at home that has one of those pullies in it... Link to comment Share on other sites More sharing options...
Team Escargot Posted November 12, 2010 Share Posted November 12, 2010 I used bearing fit (Loctit) on mine as the bearing was a sliding fit in the pulley + yes you need a big circlip. However, its very important that the belt runs centrally in the grove and is not forced in either direction. To do this line up the pulley assembly on its 2 bolt mounting and assemble it without bearing fit or circlip for a trial - then see if the pulley needs turning around or not to ofset the grove in the best direction. On mine I still needed a bit more ofset so I used 2 washers between the tensioner and the mounting on the block just to space it forward a bit. Been on now for 2 years and still runs perfectly. Nick Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted November 12, 2010 Author Leadership Team Share Posted November 12, 2010 Cheers , really useful info! Mav - do you want to swap the circlip for some spark plugs and wing stays? Edited to add - bearing now in place with Loctite bearing retainer and circlip ordered from Caterham Mav, I'll keep the bits 😬 Stu. Edited by - sforshaw on 12 Nov 2010 14:26:30 Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted November 13, 2010 Author Leadership Team Share Posted November 13, 2010 Update for information ..... The new pulley will only fit one way round - circlip/thicker rim to the front. Turn it round and the pulley fouls the mounting flange. Fully assembled the alignment is wrong therefore as Nick says, it's going to need some shims/washers behind the tensioner mount, but it's also a good opportunity to ensure the align of the pump drive pulley is correct also. Stu. Link to comment Share on other sites More sharing options...
Englishmaninwales Posted November 13, 2010 Share Posted November 13, 2010 Where can I get a new bearing for the tensioner pulley - does CC supply one? (Sorry for the hijack, Stu 😳 - just so happens I have mine in bits on the bench at the moment) Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted November 13, 2010 Author Leadership Team Share Posted November 13, 2010 Malcolm, the bearing size is 6203 which we use loads of at work ...... except that this one is 6203LHA which a bit of searching around has shown is a spec for high temperature use. They seem to be used mostly in automotive applications and not common outside the industry. I took a good look at the old one and decided it was "as new" and should have loads more life in it, so I cut the plastic pulley through to the bearing at opposite sides and just broke the old pulley away enabling the bearing to be re-used. Also, the fit of the bearing in the new pulley enables the bearing to be easily replaced in the future if there's a problem. Stu. Link to comment Share on other sites More sharing options...
Englishmaninwales Posted November 13, 2010 Share Posted November 13, 2010 Hmm..I must admit mine seems fine, but of an unknown mileage. The cost of a failure v. the cost of a new bearing! I think I'll try and get a replacement. Thanks for the detail, Stu Malcolm Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now