virden Posted September 10, 2010 Share Posted September 10, 2010 Whilst out for gentle evening's blat I came up to overtake a truck, when a large stone got thrown up and hit my windscreen. 😳 The experince definitely underlined the wisdom of wearing goggles. However said stone has left a star crack 10 mm in dia, surrounded by a ring crack 25mm dia and 3mm wide. The epicentre of the strike is located at the top RH of the screen about 40mm from the upper and side edges of the glass. Question: Whilst not in my direct line of sight, does this damage consitute an MOT failure? If so where can I obtain a new screen at sensible cost? Link to comment Share on other sites More sharing options...
Ray Pearce Posted September 10, 2010 Share Posted September 10, 2010 Check your insurance. Most will replace a windscreen for an excess of about £75. Some (like MSM) will even waive the excess if you source and replace the screen yourself. If you have an MOT coming up before you can get it fixed then consider just removing the screen - then you don't have to worry about wipers or washers either! Don't forget that this could be an ideal opportunity to try out an aeroscreen. It was for me! and now my brand new screen (courtesy of MSM) spends most of its time in bubblewrap in the spare bedroom. Link to comment Share on other sites More sharing options...
Support Team Shaun_E Posted September 10, 2010 Support Team Share Posted September 10, 2010 MOT rules here. I suspect it will be a fail as it is likely to fall within "Zone A". Yellow SL #32 - member of Drowned Rat Racing Link to comment Share on other sites More sharing options...
dalongbloke Posted September 10, 2010 Share Posted September 10, 2010 I quote "wisdom of wearing goggles". Can you believe there are aeroscreeners out there not wearing a helmet? Imagine a stone like that impacting with a forhead. Does not bear thinking about! Hope all gets sorted!! Check out Hal... http://picasaweb.google.co.uk/dalongbloke Link to comment Share on other sites More sharing options...
EFA Posted September 10, 2010 Share Posted September 10, 2010 Unbolt the screen from the stancions, turn it over, and bolt back on. Voila: Crack now on pass side.  Full Terms and Conditions of this post can be read here. Link to comment Share on other sites More sharing options...
CageyH Posted September 11, 2010 Share Posted September 11, 2010 And the hood now covers the bonnet  It's a good idea for the mot though. Only dead fish go with the flow....! Link to comment Share on other sites More sharing options...
virden Posted September 11, 2010 Author Share Posted September 11, 2010 Thanks for your suggestions guys. I like the reversal idea. I won't be going for aeroscreens, I live in a farming community and have to drive over several dairy herd crossing points. Even with a full screen I already get splashes of organics on my clothes. In similar cirumstances and aero would get banned from entering the pub! Link to comment Share on other sites More sharing options...
virden Posted September 11, 2010 Author Share Posted September 11, 2010 One last thought. When removing the windscreen from the car, are the nuts that the hex bolts fit into secured to prevent them dropping down inside? Link to comment Share on other sites More sharing options...
Bricol Posted September 11, 2010 Share Posted September 11, 2010 I was going to suggest the same thing - simply reverse the screen in the brackets, leaving the brackets attached (might have to loosen them).  But as well as the hood poppers now being on the inside, the MOT-able rear wiew mirror is perfectly placed for someone sat on the engine . . . Bri Link to comment Share on other sites More sharing options...
John Vine Posted September 11, 2010 Share Posted September 11, 2010 Neat idea re reversing the screen. As for swapping round the rearview mirror, you can get the sticky pads from any Ford dealer. JV Link to comment Share on other sites More sharing options...
CanAm Posted September 12, 2010 Share Posted September 12, 2010 One last thought. When removing the windscreen from the car, are the nuts that the hex bolts fit into secured to prevent them dropping down inside?No! You have to remove the knee trim panels to get to the nuts from the inside. Though you can get replacement retaining channels with captive nuts if you intend changing screens regularly. Alan Teenage dreams, so hard to beat. Link to comment Share on other sites More sharing options...
virden Posted September 12, 2010 Author Share Posted September 12, 2010 Can Am, thank you for telling me, you have saved my garage's resident toad and assorted mice from an explosive tirade of ancient curses as I heard the nuts dropping forever out of my reach. Link to comment Share on other sites More sharing options...
Baz Hemsley Posted September 12, 2010 Share Posted September 12, 2010 You will need a spanner on the inside. the washer and nut will drop onto a little shelf easy to recover. When replacing watch you don't trap any wires under the washers. I did and every-time I switch to main beam the fuse blew. Took me a long time to realise what I'd done. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now