John Vine Posted April 8, 2010 Share Posted April 8, 2010 Traced to a broken (brown) lead to #1 coil, just where it enters the Econoseal plug. Fortunately, it was an easy fix with a short length of wire and a soldering iron. Also, while checking over the other engine-top wiring, I discovered that the rear nearside edge of the carbon-fibre plug cover had worn through the insulation of three wires in the loom (feeds to coils and injectors). I'd guess a short-circuit was imminent . I bound each wire individually with tape, and then inserted a fat rubber grommet to protect the cable loom where it passes under the plug cover. Has anyone else encountered these problems? JV Edited by - John Vine on 16 Jun 2010 17:54:46 Edited by - John Vine on 22 Jun 2010 17:39:32 Link to comment Share on other sites More sharing options...
spiderlane Posted April 8, 2010 Share Posted April 8, 2010 Hi John That's interesting - it seems that my car (R400 SV) already has a grommet there if I understand you correctly. See this picture -> http://gallery.me.com/mark.lane#100193/Fourth-20Day-20of-20Build--20Wiring-20and-20Plumbi_2&bgcolor=black Perhaps yours was missing, or it was something they added to the design later? ETA - Link, Clarity Edited by - spiderlane on 8 Apr 2010 15:19:53 Link to comment Share on other sites More sharing options...
John Vine Posted April 8, 2010 Author Share Posted April 8, 2010 Yes, Mark, that's the fella. My engine (April 2008 kit) was supplied without the grommet. Also, your loom is slightly different. You seem to have the main loom plus a separate bunch of wires passing through the grommet. My loom is all bound together as one. So, it looks as though CC have modified the design. JV Link to comment Share on other sites More sharing options...
Angus Posted April 8, 2010 Share Posted April 8, 2010 I also have spotted this engine loom chafing problem on mine - a late 2007 kit. I have made a partial improvement by lining the cut-out in the coil cover with a bit of the CC-supplied cycle wing edging. Not ideal because the loom underside can still chafe on the metal edge of the cam cover. I like the idea of the grommet - I will try and get one from CC. Suggest other Duratec owners check their engine looms. Angus Link to comment Share on other sites More sharing options...
Gasmaninaseven Posted April 8, 2010 Share Posted April 8, 2010 Mines an early 2007 kit; I've had the broken wire where it enters the plug to the coil; fixed that and in due course had a new engine loom under warranty. Had another misfire which I assumed was the same again, but this time coil pack failure ( this one was different to the other three and labelled as a "test" item ) I've hitched up the loom to try to prevent chafing- mine looks different to Spiderlane's too. Neil Build pictures here Guantanamo Bay Orange SUPERLIGHT R400...... Link to comment Share on other sites More sharing options...
Tangerine Dream Posted April 9, 2010 Share Posted April 9, 2010 That's interesting - it seems that my car (R400 SV) already has a grommet there if I understand you correctly. See this picture -> http://gallery.me.com/mark.lane#100193/Fourth-20Day-20of-20Build--20Wiring-20and-20Plumbi_2&bgcolor=black FWIW, my 2010 factory build has wiring & grommet pretty much as shown in the quote. Only difference is the smaller loom is tied to the bigger. ================================== R400SV in orange - so far unmodified! Link to comment Share on other sites More sharing options...
spiderlane Posted April 9, 2010 Share Posted April 9, 2010 Hi TG - I don't suppose you have any pictures of the general wiring layout and routing in the engine bay? I've wired up my engine, but not cable tied things down yet and I'd love to see how the factory do it. Thanks Mark (Sorry about the thread hijack) Link to comment Share on other sites More sharing options...
Tangerine Dream Posted April 10, 2010 Share Posted April 10, 2010 Well the factory missed off my aero whiskers and it seems now gave me the wrong brake cylinder cap! But, yes, you are welcome to some pics. I will take a few today. ================================== R400SV in orange - so far unmodified! Link to comment Share on other sites More sharing options...
spiderlane Posted April 10, 2010 Share Posted April 10, 2010 Ah yes, the joys of owning a low volume British sporstcar - I know exactly how you feel :) Thanks for the offer of pics, much appreciated Mark Link to comment Share on other sites More sharing options...
Tangerine Dream Posted April 10, 2010 Share Posted April 10, 2010 OK, I have just taken a few. Photobucket allows me up to 1024X768. If you need a fuller resolution one then send me a private message and I will email it. I have done my best to make contrast OK but actually have almost zero idea how to use image editing tools! This link will get you there ================================== R400SV in orange - so far unmodified! Link to comment Share on other sites More sharing options...
spiderlane Posted April 10, 2010 Share Posted April 10, 2010 Thanks TG, very much appreciated and useful beyond the wiring because it shows the hose layouts for the DS breather and expansion bottle which is the job I've been doing today. Link to comment Share on other sites More sharing options...
sjmmarsh Posted April 26, 2010 Share Posted April 26, 2010 How do you tell if the coil packs are OK? (CSR 260) I was at Cadwell today - on the last session the engine seemed to stutter slightly - I still got my best lap time of the day though (data logger - analysed at home). On the way back, the stutter got worse but was intermittent as well. It feels like the rev limiter is cutting in momentarily (but around 3k) and was more likely to happen on a light throttle setting, making cruising at 60 interesting at times. Any advice appreciated. Steve Link to comment Share on other sites More sharing options...
John Vine Posted April 27, 2010 Author Share Posted April 27, 2010 Steve, Some possible checks... After a period of misfiring, is one primary cooler than the others? Are the wires that enter each coil 2-pin plug sound? That was where my trouble started, and even with one wire completely broken, that cylinder continued to fire, albeit intermittently, due to an occasional sparky contact I suppose. Are the pins clean, with the spring strip making a good electrical contact? Having removed the pin to repair my broken connection, I discovered that the contact area was a bit carbonised, and the little spring pad was squashed a bit. Cleaning everthing in meths, and prising up the spring to increase contact pressure, seemed to fix it. As for the coils, I've no idea how to check them. A local Ford dealer told me that these coils could be unreliable. Maybe you could take all four into your nearest and ask them to test them for you? JV Link to comment Share on other sites More sharing options...
sjmmarsh Posted April 27, 2010 Share Posted April 27, 2010 Thanks for the pointers John. I will check the wiring tonight, particularly as the coil cover lost a bolt early in the day. Interestingly I have always had a misfire, but as it only ever happened 3 or 4 times a year and CC couldn't fix it, I have just lived with it. It only presented at around 4000 rpm under full throttle acceleration. Not every time either. I have order two coil packs just in case (I need the car this weekend and they won't go off) as I understand they tend to fail in pairs. Does anyone know the pairing? 1/4 and 2/3 seem to be common for other engines but could not find duratec specific info. Steve Steve Marsh My Caterham Page Link to comment Share on other sites More sharing options...
sjmmarsh Posted April 27, 2010 Share Posted April 27, 2010 John The wiring looks ok and there was nothing odd with the coil packs. I did a temperature check of the primaries. After about 2 mins idling, three of them were at 250C and one was 400C (the front primary), but measuring about 6" further down the pipe, they all were around 220C.. Not sure what that is telling me! Steve Link to comment Share on other sites More sharing options...
John Vine Posted April 28, 2010 Author Share Posted April 28, 2010 Steve, The nice even temps seem to suggest that the motor's not missing when idling. It would be good if you could repeat the test during a brisk run at the point when you detect misfiring. When I had my problems, I quickly took the bonnet off and gingerly touched each pipe in turn (I had no meter handy). #1 was noticeably cooler than the others, which at least indicated where I should look first. You mentioned a datalogger. Is it capable of tracking exhaust temps, misfires etc? Re your coils etc, you mentioned pairs, so I imagine the CSR260 set-up is different to the R400. I have four separate coil-over-plug assemblies, each fed independently, and all having the same P/N. I bought a spare from a Ford dealer, and he confirmed that there was only the one variety for my engine (also used on the Focus, I believe). Perhaps a query to Cosworth might elicit something? JV Link to comment Share on other sites More sharing options...
John Vine Posted June 16, 2010 Author Share Posted June 16, 2010 An update.... CC Engineering have recently developed a revised R400 Duratec coil sub-loom. It's described in Workshop Notice WN515 and called a "flexi-coil loom" -- P/N 3AL080A. BM me if you'd like a copy of the WN. It requires the existing coil loom to be cut out and a 6-pin plug inserted to connect in the new loom. I've just ordered it (£27.50 + P&P), and will report back once I've fitted it. JV Link to comment Share on other sites More sharing options...
John Vine Posted June 17, 2010 Author Share Posted June 17, 2010 Andrew, YHM. Angus, I've just tried to reply to your email but it was rejected. The error message said it couldn't recognise "world.com". I think maybe there's an error in your BC profile address. It seems to read "nt; world.com". I've tried re-sending the email to "ntlworld.com", hoping that's correct. JV Link to comment Share on other sites More sharing options...
Angus Posted June 18, 2010 Share Posted June 18, 2010 John Thanks, and YHM Yes, sorry, typo in my mail address. You guessed correctly ! Angus Link to comment Share on other sites More sharing options...
John Vine Posted June 22, 2010 Author Share Posted June 22, 2010 A further update... I've now fitted the flexi-coil loom. There are lots of pics here. It was pretty straightforward, but here are a few tips: # When ordering, be sure to ask CC to send you the 6-pin male connector and the little yellow insert. You need this to hook into the engine loom (according to WN515, the R500 already has this connector fitted). These bits weren't included with my loom (3AL080A). # You'll need a wire-stripper, a crimping tool and some cable ties. # The coil-on-plug (COP) connectors each have two wires. Pin-1 is the +ve feed and Pin-2 the ground wire. On my car, all the ground wires were white-orange, compared to WN515 which said white-purple. # There are eight engine-loom wires to be joined to six connector pins. You'll need to double-up the ground wires on pins 2 and 5 (see the wiring guide in WN515 or on the link above). It doesn't matter which ground wires make up each pair. Here's how to do it: 1. Cut off the eight COP wires about 10cm from where they disappear into the engine loom, and strip off about 3mm of insulation from each stub (no more, otherwise you risk obstructing the pin-locating tab in the connector). 2. Slide a little yellow rubber seal over the end of each wire stub (or pair of wires for the ground wires), crimp the bared wire and then close up the seal grip. 3. Insert each pin into the connector in turn (see wiring guide), and (gently) pull through from the other side with a pair of long-nosed pliers. A click indicates that the pin is located correctly. 4. Push in the yellow plastic insert, ensuring that each pin protrudes equally, and connect up. 5. Secure the wiring with cable ties. Job done!JVETA: I've now repaired the busted link above.ETA-2 (20Jul23): Due to Photobucket's nasty and unfriendly money-grubbing policy re free photo storage, my account has been deactivated. I've no intention whatever of paying them to reactivate my account, so if anyone would like the photos concerned, please send me a Private Message with your email address. Link to comment Share on other sites More sharing options...
Angus Posted June 22, 2010 Share Posted June 22, 2010 John Excellent write-up. Angus Link to comment Share on other sites More sharing options...
John Vine Posted June 22, 2010 Author Share Posted June 22, 2010 Thanks, Angus. Following your email about crimping tools, I thought I ought to alert readers to the fact that I didn't use the "correct" crimping tool for these AMP Econoseal J-series connectors, mainly because I couldn't find one. The correct tool crimps the contact and the seal grip simultaneously into a "B" shape. The tool I used (also an AMP, in fact) didn't have the correct die shape so I folded the tabs firmly flat instead (probably the second best option). Don't use pliers to do this -- they're a definite no-no as they won't exert sufficient pressure. If anyone should manage to locate a source of the correct crimping tool, please tell me. JV Link to comment Share on other sites More sharing options...
Rattie Posted June 23, 2010 Share Posted June 23, 2010 If Neil at Polevolt doesn't have it, you probably didn't need it... Crimp Tool for Econoseal etc Martyn R300GRR Link to comment Share on other sites More sharing options...
John Vine Posted June 23, 2010 Author Share Posted June 23, 2010 You must be a mindreader, Martyn. I asked Pole Volt this morning for advice as they sell the connectors. Back came an email from Neil, about the same time as your post, recommending exactly the tool you mention (TT320). The only snag is that they won't have any stock for 7 days or so. JV Link to comment Share on other sites More sharing options...
John Vine Posted June 24, 2010 Author Share Posted June 24, 2010 Crimp-tool update.... The folks that make (some of) CC's looms tell me they use a Pressmaster tool, obtainable from here. They suggest the crimp-tool frame (stock no. 492-9595) plus a suitable die set (492-9668 or 492-9674, depending on the wire size). These aren't cheap-o products though. The frame plus one die comes to around £65 plus VAT and P&P. JV Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now