Sam Monoogian Posted December 30, 2009 Share Posted December 30, 2009 Photos for most of the below items can be found here All items can be collected from Thatcham or posted at cost. Set of 4 wheels on Ford PCD, two with CR322 tyres (pictured) that have done about 200 miles (but are 4 years old) and the other two with tyres that should be immediately replaced Not my personal choice of DIY painting either but would do as a cheap set of 2nd track wheels possibly. £30 ono - - SOLD Pair polished windscreen stanchions from 1997 car. The left hand one needs polishing up after one of the socket cap screw hex's rounded and I removed it with a hacksaw blade. £15 (pictured) - SOLD Pair crossflow engine mounts. £10 (pictured) Crossflow rear exit exhaust silencer and rear pipe only. Includes rear mounting strap. £20 Crossflow oil pump with Mocal take-off for oil cooler £15 (pictured) Crossflow starter motor - 3 years old but only 2000 miles on car. 10 tooth pinion. £30 Zetec items - brand new from Focus 2.0 Zetec, removed from my ill-fated Raceline engine - now on ebay, user profile link a few posts down: Complete clutch Complete intake manifold Original wet sump NtL items: Fuel filler - bezel only (pictured) Standard front brake callipers - no pads (pictured) Crossflow Alternator Strap (pictured) VDO Oil pressure gauge and sender, 0-5bar - 1995 era, rust spots around bezel (pictured) VDO Water Temperature Gauge (pictured) Bonnet from 1980 Caterham with modified cutout - in rather "fetching" shade of green Need to clear the garage fairly sharpish so collection within the next week preferable and essential by beginning of February. Edited by - Sam Monoogian on 2 Jan 2010 13:30:40 Edited by - Sam Monoogian on 5 Jan 2010 20:23:21 Link to comment Share on other sites More sharing options...
dalongbloke Posted January 3, 2010 Share Posted January 3, 2010 Hi Sam... I am interested in the wheels and tyres... would a daytime pickup be possible for you? I get over to Hungerford most weeks in a van..... Andy on dalongbloke at aol.com Check out Hal... http://picasaweb.google.co.uk/dalongbloke Link to comment Share on other sites More sharing options...
Sam Monoogian Posted January 4, 2010 Author Share Posted January 4, 2010 Andy, My work is only 2 miles from where I live so I can pop back during the day. Lunchtime between 12.30-2pm is preferable though times outside this would not be a massive drama. There was a slight complicating factor when I realised today that the two wheels with old tyres on are down in Worthing at my parents place but I see conveniently you're based in Worthing. Following pick-up of the two I've got here would you be happy to pick the other two up in Worthing? I'll blatmail you my phone number. Link to comment Share on other sites More sharing options...
GHPT Posted January 4, 2010 Share Posted January 4, 2010 Hi I am interested in the Zetec bits. What are you looking for the clutch and intake manifold. Could I mount some weber 45's on it? George :) Link to comment Share on other sites More sharing options...
millsn Posted January 4, 2010 Share Posted January 4, 2010 seconded for the clutch. Can you explain what sort of power it's designed to take? / sort of / spec of clutch? Link to comment Share on other sites More sharing options...
Sam Monoogian Posted January 4, 2010 Author Share Posted January 4, 2010 My wording possibly wasn't the clearest. All the Zetec bits are the OEM fitment for installation into the Focus/Mondeo that the engine might have gone into. I've got them as I removed them and fitted a Raceline sump and intake manifold to take Webers, and put an aftermarket clutch on. The bits I have available are a Sachs OEM clutch assembly, the plastic swan neck intake manifold complete with injector rail and injectors and the deep two-part sump. I've now put these bits on ebay as realise they're not that attractive to Zetec Seveners. Ebay profile here. Link to comment Share on other sites More sharing options...
alextangent Posted January 4, 2010 Share Posted January 4, 2010 Hi Sam, How many teeth are there on the starter motor? 9 or 10? Alex McDonald Loud, louder, loudest... Link to comment Share on other sites More sharing options...
Molecular--Bob Posted January 5, 2010 Share Posted January 5, 2010 Hi Sam Noticed you have a zetec thermostat housing on Ebay. Is this for a blacktop? and if it is would you have a price in mind for selling it direct rather than Ebay? Cheers Ian B Link to comment Share on other sites More sharing options...
Sam Monoogian Posted January 5, 2010 Author Share Posted January 5, 2010 Alex, the starter pinion has 10 teeth. Ian, I didn't have a price in mind, but seeing as some housings are priced at £30 and there's another assembly up for £25, I'd say £20. Link to comment Share on other sites More sharing options...
Molecular--Bob Posted January 5, 2010 Share Posted January 5, 2010 Hi Sam Seems like a very fair price. If you would rather let the auction run i am happy to take my chances and bid on it, I am only after it as a spare in case i screw up tapping my current one for the DTA temp sender that i need to fit. if you are happy to sell then blat mail me and we can sort out payment and postage. Cheers Ian B Link to comment Share on other sites More sharing options...
Sam Monoogian Posted January 6, 2010 Author Share Posted January 6, 2010 Ian, Happy to end it early, in fact I have Will blatmail you imminently. Link to comment Share on other sites More sharing options...
dalongbloke Posted January 6, 2010 Share Posted January 6, 2010 Hi Sam, please consider tyres and wheels sold, will see you friday week weather permitting. If anyone else whant GONADS help, will be bringing items back to Worthing, can also drop into Wandsworth/Chelsea area weekly. Regards Andy Check out Hal... http://picasaweb.google.co.uk/dalongbloke Link to comment Share on other sites More sharing options...
MXM Posted January 27, 2010 Share Posted January 27, 2010 Emailed about engine mounts. Link to comment Share on other sites More sharing options...
oddjob Posted January 27, 2010 Share Posted January 27, 2010 Hi Sam, If still available I would like to buy the following items:- xflow engine mounts, exhaust silencer and tail pipe and starter motor,at listed prices. Regards David Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now