david nelson Posted October 28, 2007 Share Posted October 28, 2007 I am changing my dash and currently have the dash and scuttle removed. The is no windscreen wipe bar for the loom to attach too ( to keep it up). Any ideas how to attach the loom so it does not fall down? thanks David Link to comment Share on other sites More sharing options...
w7rren Posted October 28, 2007 Share Posted October 28, 2007 cable tie with rivet fixing These may do the job ? Born again sevener 1st time around back in 1991 Link to comment Share on other sites More sharing options...
Mick Day Posted October 28, 2007 Share Posted October 28, 2007 I used a length of bamboo. Ty wrap one end to the wiper motor bracket & the other end to the steering column. Link to comment Share on other sites More sharing options...
Harry Flatters Posted October 28, 2007 Share Posted October 28, 2007 Bamboo - what do you this this is Mick, the Morgan owners site 🤔 😬 *arrowright*Harry Flatters *arrowright* AKA Steve Mell - Surrey AO and Su77on Se7ener Link to comment Share on other sites More sharing options...
david nelson Posted October 28, 2007 Author Share Posted October 28, 2007 An old carbon fibre fishing rod would be ok. Link to comment Share on other sites More sharing options...
Julian Thompson Posted October 28, 2007 Share Posted October 28, 2007 😬 Link to comment Share on other sites More sharing options...
Leadership Team SLR No.77 Posted October 29, 2007 Leadership Team Share Posted October 29, 2007 Why not a section of aluminium tube from B&Q 🤔 Stu. www.superse7ens.co.uk..........the rebuild 😬 Link to comment Share on other sites More sharing options...
metal mickey Posted October 29, 2007 Share Posted October 29, 2007 Why not make up a false inner firewall that sits in the same groove that the existing one does. Shape it with a fold in the top and bottom to form a small void between the two then fasten everything to if neatly. You can then fit/remove the whole scuttle assembly at will and leave the wiring in situ to work on. I did this on my rebuild and it works well. Link to comment Share on other sites More sharing options...
captain chaos Posted October 30, 2007 Share Posted October 30, 2007 MM, Nice idea..got any pics? Gary Link to comment Share on other sites More sharing options...
JACK FLASH Posted October 31, 2007 Share Posted October 31, 2007 This might sound like a stupid idea, but when considering taking my scuttle off, I was thinking of only removing the outer body panel and leave the vertical panel in place. Everything connected to the vertical panel would stay in place, more or less that is, without all the problems of disconnecting the wiring loom from the fuse boxes and pulling the wires that go through the vertical panel to the engine bay. In order to do this, I would have to drill out all the rivets but I was also thinking of replacing them afterwards with small bolts and locknuts. So it would be a quick job later to remove the scuttle for working on the instruments or on the wiring loom. Is this idea any good or am I completely on a wrong track ? ! Link to comment Share on other sites More sharing options...
metal mickey Posted October 31, 2007 Share Posted October 31, 2007 Gary - blat mail me your email and i'll send you a piccy. Jack - replacing all the rivets on the scuttle with rivnuts is one option but do you want to undo all those pins to remove the scuttle 🤔 My system - remove 4 scuttle securing bolts, 2 bolts through steering column bracket and if fitted wiper nuts and lift off complete scuttle and screen/areo's. you may have to disconnect heated screen wires if fitted. Link to comment Share on other sites More sharing options...
Leadership Team Mcalvert Posted October 31, 2007 Leadership Team Share Posted October 31, 2007 Mike - each to their own I replaced my rivets with rivnuts (24 if I remember rightly) - takes a minute to undo them all as long as you have an electric screwdriver with the right attachment! Regards - Michael. Link to comment Share on other sites More sharing options...
JACK FLASH Posted October 31, 2007 Share Posted October 31, 2007 I' m glad that other people have the same ideas as me and that they have tried them out with good result. So I' m certainly going the same route. I have the specific problem that there are a lot of extra items hanging on the vertical panel of the scuttle (contact breaker cutout boxes, oil separator and oil catch tank, cooling header tank, ...) and I don' t want to dream of dismounting them each time when I have to do something on the wiring loom or instruments. Michael, which type of rivnuts did you use ? I was thinking about nuts and bolts but obviously rivnuts seem to be better. Did you have to make some sort of reinforcements or is the aluminium thick enough to screw in the rivnuts ? Link to comment Share on other sites More sharing options...
Leadership Team Mcalvert Posted October 31, 2007 Leadership Team Share Posted October 31, 2007 No problem at all with riv-nuts in the ali. I then used some really tarty red anodised bolts to fit in them Michael. Link to comment Share on other sites More sharing options...
Julian Thompson Posted October 31, 2007 Share Posted October 31, 2007 The only thing is that if you want to take the scuttle off often if you leave the complete vertical piece in place you end up with a very wobbly scuttle panel with not much rigidity - quite prone to damage in handling. Also, obviously, you have to undo lots of bolts to get it off. Not saying it isn't better than fixed scuttle but it's just a point. You could make a half vertical panel that allows you to keep many items mounted to it and which stays in position - the other half would lift. Personally I have made a couple of ally panels that house the wiring and take care of the steering column. My scuttle comes off with 4 knurled thumbscrews in about 30 seconds.... here Link to comment Share on other sites More sharing options...
Julian Thompson Posted October 31, 2007 Share Posted October 31, 2007 Actually this one is better... here Link to comment Share on other sites More sharing options...
metal mickey Posted October 31, 2007 Share Posted October 31, 2007 Julian - very similar idea,slighly different execution Michael, really , red anodised screws Link to comment Share on other sites More sharing options...
Julian Thompson Posted November 1, 2007 Share Posted November 1, 2007 One thing all the ideas will have in common is that we will all tell you it transforms how nice it is to work on the wiring on these things *thumbup* It's a massive improvement! Guess mine will all be redone during my masssssive winter rebuild of the old shed 😬 Link to comment Share on other sites More sharing options...
metal mickey Posted November 1, 2007 Share Posted November 1, 2007 Definately Link to comment Share on other sites More sharing options...
captain chaos Posted November 1, 2007 Share Posted November 1, 2007 If further proof was ever needed, those photo's of Julian's dash gives even greater credance to my decision to allow him to be the electrical engineering consultant on my re-build Link to comment Share on other sites More sharing options...
Julian Thompson Posted November 1, 2007 Share Posted November 1, 2007 To be honest Gary that isn't really that neat. It's just kind of the best I could do from what Nick and Graham had left on there without stripping it all out and starting again... which is what I'm doing this winter. Really, the connectors are very basic and the fusing strategy leaves a lot to be desired. Finally the layout in terms of the mix of data and high current cables is quite poor though I've had no problems but that's more luck than judgement. At the end of the day there is no substitute for simple but careful planning from scratch - works every time. Also, no matter how good or experienced at wiring looms you think you are it's one of those jobs that never takes any less time!! Link to comment Share on other sites More sharing options...
JACK FLASH Posted November 2, 2007 Share Posted November 2, 2007 Red anodised screws might look good, for exampe on a green fluorescent car. I' m just going to stick with standard aluminium of dull black anodised screws. The problem with the possibility of "weakening" the scuttle was my major concern, but after reading the several remarks and ideas, I' m thinking of making a full length reinforcement vertical plate for the inside. I' m also considering taking a thick copper plate for this reinforcement and wire it directly to the chassis earth. Afterwards I can earth each "dashboard item" separately on this copper plate, thus avoiding the known earthing problems. For example at the moment the instrument illumination isn' t working because I' ve got only 4 V on the bulbs. ☹️ Link to comment Share on other sites More sharing options...
elie boone Posted November 2, 2007 Share Posted November 2, 2007 My scuttle had a lip witch goes under the horizontal plate where the heater should be, it's very difficult to take the scuttle off without distorsion. ( 1999 LA chassis ) I am used to dive under the dacsh, keeps me fit 😬 Link to comment Share on other sites More sharing options...
JACK FLASH Posted November 4, 2007 Share Posted November 4, 2007 Elie, Strange scuttle, you' ll certainly have to show or explain it to me when I pay you a visit. I only hope that my scuttle hasn' t got this lip because my back really demands a solution. 🙅🏻♂️ Link to comment Share on other sites More sharing options...
Atinod Posted November 5, 2007 Share Posted November 5, 2007 Julian, Very nicely done *thumbup* I bet that horn position makes you jump though James Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now