Tony C Posted April 10, 2007 Share Posted April 10, 2007 2003 SV How much of an interference fit should there be between the bearing and the wishbone? While checking out strange noises from front nearside, heard when pushing the 7 back into the garage, I noticed it was possible to get vertical movement on the L/H upright. I could see that the spherical bit was moving up and down within its race. (The fibre lining is coming out one side). Checked with CC this morning and ordered a new pair of bearings - Sod's Law being what it is, the offside might not be far behind - though it's fine at the moment. I looked at all the good information in the "Search" and decided to remove the wishbone from the car so I could use the press at work to remove and refit the bearing. Just finished taking it off and once the spiral "Circlip" was removed the bearing just fell out of the housing. There is evidence that the outer race has been rotating within the wishbone. The bearing is very shiny on its outside face and the wishbone housing looks corroded. The bearing easily slides in and out and can rotate freely. If, as I suspect, the wishbone housing is worn, the new bearing will also be free to rotate even when using Loctite “Bearing Fit” as advised. I’ll try it first of course, but it looks like I might need a new wishbone 🙆🏻 BRG Brooklands SV 😬 It seems that perfection is achieved not when there is nothing more to add, but when there is nothing more to take away. (Antoine de Saint-Exupery) Edited by - Tony C on 10 Apr 2007 21:52:41 Link to comment Share on other sites More sharing options...
Englishmaninwales Posted April 10, 2007 Share Posted April 10, 2007 Tony Sounds a bit loose to me . I don't use a press to get them in or out,just a hammer and a spacer, but they are not as loose as you describe. Malcolm Link to comment Share on other sites More sharing options...
shn7 Posted April 10, 2007 Share Posted April 10, 2007 Replaced mine in the past and they didn't fall out when the circlip was removed. I used a bench vice and a couple of suitably sized sockets to press them out. Some wear in my current ones was spotted at MOT last week so seems I may be having to do them again soon. Loctite definitely required. Steve. West Sussex AO Not forgetting Percy the Polar Bear Link to comment Share on other sites More sharing options...
Johnty Lyons Posted April 10, 2007 Share Posted April 10, 2007 I've just replaced mine I had to use a lot of force with a presss to get them out BUT the new one fell in You need to use the correct Loctite and its Activator good idea to replace cicrlips as well. jj N.I. L7C AR. Membership No.3927. Link to comment Share on other sites More sharing options...
shn7 Posted April 11, 2007 Share Posted April 11, 2007 Johnty, Which Loctite are yuo referring to that requiress and activator? When I fitted my last ones I checked the Loctite webbie and got to one that was a stud and bearing lock but doesn't require an activator Steve. West Sussex AO Not forgetting Percy the Polar Bear Link to comment Share on other sites More sharing options...
Tony C Posted April 11, 2007 Author Share Posted April 11, 2007 Loctite 641 here. Looks like it is good for gaps up to 0.25mm (72 hour cure). Sliding fit I guess manufacturing tolerances between bearing and housing can give different levels of fit - I'll check with CC - maybe I had a small bearing and a big hole and the looseness caused the PTFE liner to migrate. What appears to be corrosion in the housing might be Loctite Bearing Fit residue. Thanks for the info. BRG Brooklands SV 😬 It seems that perfection is achieved not when there is nothing more to add, but when there is nothing more to take away. (Antoine de Saint-Exupery) Link to comment Share on other sites More sharing options...
Tony C Posted April 11, 2007 Author Share Posted April 11, 2007 Bright lamp and a magnifying glass shows the bearing housing is heavily pitted with corrosion. New wishbone ordered 🙆🏻 BRG Brooklands SV 😬 It seems that perfection is achieved not when there is nothing more to add, but when there is nothing more to take away. (Antoine de Saint-Exupery) Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now