Paul Gibb Posted March 23, 2007 Share Posted March 23, 2007 Having just reinstalled my Vx engine I now cannot get the starter motor to turn over . Silence on depressing starter button and an ominous click from the starter on releasing it . Shift lights and dash lamps are on & fuel pump primes with ignition on. The battery is apprently fully charged with 12.4v across terminals with ignition dropping to 11.6v with depression of starter button. Boosting with my external battery pack has no effect ☹️. I have inspected and cleaned earths to block and attemted to test the starter by isolating it and applying +ve from a spare charged battery to the terminals - nothing happens 😔 should it? Last night I was reduced to going round in circles completely knackered hoping that something would change whilst my back was turned or I was making coffee - it did not If I remove the starter how can I test taht it is functioning (& how will it earth if removed from the block?) Any thoughts most welcome as I hope to leave for Llandow v early on Friday am. As I will probably not have acces to blatchat until return from work today apologies for lack of replies to your suggestions which will all be most appreciated . Please bear in mind when writing that you could write what I know about electrics on the back of a very small postage stamp. L7 FUN Link to comment Share on other sites More sharing options...
tiddy1 Posted March 23, 2007 Share Posted March 23, 2007 There are 2 parts of the starter to test and it can be done in situe with a set of jump leads or similar. 1 disconnect the battery, 2. connect jump leads or flying leads to known good battery 3. clamp the -ve lead on to the starter body, or any good earth 4. touch the +ve onto the terminal on the back of the starter. this is the big one which is connected to the solenoid by a big wire the starter should spin, but not engage with the flywheel if it does then the motor part is ok next test the solenoid Keep the earth connection and touch the +ve onto the solenoid terminal ( the one with the thin wire attached) this should result in a hefty clunk as you hear the solenoid pull in if this works then the solenoid is ok and you should start troubleshooting wires and relays Simon Link to comment Share on other sites More sharing options...
Rob Walker Posted March 23, 2007 Share Posted March 23, 2007 Paul, I would test it on the car. You should have a heavy cable from battery +ve to the main +ve terminal on the starter motor and the block should also be connected to the -ve of the battery by a heavy cable. All you need to do is take a thin bit of wire from battery +ve to the actuator (small terminal) and the starter motor should operate. If nothing happens and your battery is fully charged then suspect the pre-enguage solenoid. Rob Link to comment Share on other sites More sharing options...
susser Posted March 23, 2007 Share Posted March 23, 2007 Sounds like you might have just done this; "attemted to test the starter by isolating it and applying +ve from a spare charged battery to the terminals - " The easiest (but not neccessarily the safest) way to test a starter's windings is to take a reasonably thick bit of wire from the positive battery terminal to the terminal that has the wire on that goes into the starter's casing. On a pre-engaged starter, that will just kick it over. On an inertia starter (with no piggyback solenoid) it will engage it. Make tis test a very short one. a quick flash across the terminal will tell you whether the windings are open circuit. (5hagged). Wear some gloves and Safety glasses. Not for the faint hearted and I'm sure Health and safety Man will be along in a moment to nail me to the wall. Please feel free to ignore these ramblings at the faster typing more accurate thinkers above have it covered. 😳 Edited by - susser on 23 Mar 2007 08:30:29 Link to comment Share on other sites More sharing options...
F355GTS Posted March 23, 2007 Share Posted March 23, 2007 Paul I have a spare here if you are desperate, if you are off to Llandow I'm kind of on the way from you Call if you need it 07831 662630 Mark Link to comment Share on other sites More sharing options...
DaveK Posted March 23, 2007 Share Posted March 23, 2007 Paul IIRC you are running the small 233mm flywheel with the offset drive starter. I cannot help with the testings as its more than covered above, however i have a spare offset starter to suit the flywheel if you wish to borrow it. Cheers Dave Link to comment Share on other sites More sharing options...
Old Septimus Posted March 23, 2007 Share Posted March 23, 2007 If it's off the car make sure it is very securely clamped in a large vice before applying any current. I've seen someone energise one lying loose on the floor and the torque reaction had it bowling all over the place bouncing off things. Link to comment Share on other sites More sharing options...
alextangent Posted March 23, 2007 Share Posted March 23, 2007 Doubly agree with off the car testing. I've sent a starter solenoid core an inch past my left ear and right through a paneled wooden fence . Don't go there ; if it's off the car, best getting your local garage to test it if you value your health. Alex McDonald A loud 1700 SS Link to comment Share on other sites More sharing options...
Stationary M25 Traveller Posted March 23, 2007 Share Posted March 23, 2007 Off-topic I know, but I recall a college lecturer 30+ years ago tell us never to hand-hold stuff around a lathe in the metal-working machine shop. Same chap wanted to test the output from his cars dynamo (yes - that ages it !), so he clamped the shaft in the jaws of the chuck, held the body of the dynamo in his hands (but dead straight mind you !), then had someone start the lathe on a slow speed. You've guessed it - dynamo flew out of his hands and clear over our heads (fortunately ) and hit the floor 20 feet away !! Exit one rather embarrassed lecturer ****************** And you run and you run to catch up with the sun, but it's sinking... And racing around to come up behind you again. photos Link to comment Share on other sites More sharing options...
Paul Gibb Posted March 23, 2007 Author Share Posted March 23, 2007 Well thank you all for your advice on testing, your clear explanations & your very generous offers to lend spares . The fault is definitely located within the starter which is making some contact with the flywheel ring gear but not turning over. On the plus side this is easily fixed and I can arrange to pack a spare in future as I do with most other of my non standard ancillaries . L7 FUN Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now